Postea QubeVu DimStation Quick Start Manual

Hide thumbs

page of 22

/ 22
Bookmarks

Quick Links

Download this manual

QubeVu QuickStart

DimStation assembly

and setup

Summary of Contents for Postea QubeVu DimStation

Page 1 QubeVu QuickStart DimStation assembly and setup...
Page 2 Welcome to QubeVu DimStation, the Instant Dimension Invention. This guide will assist you in assembling and setting up your new DimStation. minutes...
Page 3 1 Inventory Carefully unpack and Pole familiarize yourself with everything in the box. Power cord Base Hex wrenches Ethernet cable Calibration box Display Head DimStation Quickstart...
Page 4 2 Begin pole assembly Locate the two screws loosely pre-installed at the pole joint. Using the appropriate hex wrench, remove them and set them aside. Leave the other two screws in place. 3 Assemble pole Taking care not to strain the cables, lay the pole out on the floor (preferably on a rug or similar soft surface).
Page 5 5 Remove power block screws Lay the pole over a table or the arms of a chair for this step. Remove the four bolts that are pre-installed in the block at the bottom of the pole. 6 Attach base With the power block hanging off the edge of the table, insert the two pins in the base into the matching holes in the power...
Page 6 Cable shroud 7 Complete pole Stand the complete, assembled pole upright. To make the rest of the assembly process as simple as possible, review the names of the DimStation’s parts at left. Display cable Power block Base...
Page 7 8 Remove cable shroud cover Loosen the four bolts that secure the top of the cable shroud. Do not remove them. Slide the shroud cover back and lift it off. Set it aside. 9 Begin attachment of head Align the head with the cable shroud at the top of the pole.
Page 8 10 Cable names Note that the cables are labeled. 11 Port names The ports on the back of the head are also labeled. 12 Attach cables Order Cable label Port label Use this guide to correctly connect cables to their ports, in Ethernet Ethernet the listed order.
Page 9 13 Align the head Gently folding the cables into the cable shroud, insert the bolts on the head into the keyhole slots on the shroud. Do not tighten them yet. 14 Reattach shroud cover Put the top back on the shroud cover.
Page 10 16 Prepare the display Loosen the bolt that holds the U-shaped display bracket. 17 Remove cable cover Remove the cable cover in the bottom corner on the back of the display. You won’t need this again. 18 Choose display location The display is usually mounted just above the display cable opening.
Page 11 Mount the display Mount the display to the pole at your chosen location by re-tightening the bolt on the U-shaped bracket. 20 Connect the display cable Attach the display cable to the mini-USB port located where you removed the cable cover in a previous step.
Page 12 19 Place a scale If you’re not using a scale, skip this step. If you’re using a scale, place it on DimStation’s base. Center it from side to side. To locate your scale front-to- back, find the small groove Center the scale engraved on both edges of on the engraved lines on the base...
Page 13 Your DimStation is now ready to be plugged in. When it is, the software setup process will begin automatically. Don’t plug in your DimStation unless you have a few minutes to complete all of the setup steps. m inutes DimStation Quickstart...
Page 14 1 Initiate setup When you start your DimStation for the first time, the setup wizard will launch automatically. Touch the arrow button to begin setup. 2 Accept the User Agreement Review the End User License Agreement (EULA) by using the up and down scroll buttons on the right hand side.
Page 15 3 Set your time zone Select your time zone, and then touch the checkmark to continue. 4 Adjust the date and time Adjust the date and time if necessary, and then touch the checkmark to continue. DimStation Quickstart...
Page 16 5 Calibrate Zero Height Zero Height calibration allows DimStation to calculate the distance between the scan head and the base. The process differs depending on whether the base is flat or uneven. If your base is a smooth-topped scale or the DimStation base, touch the left button.
Page 17 7 Zero Height continued It is important to keep DimStation’s base clear and unobstructed during zero height calibration, so that it can set Zero Height accurately. 8 Zero Height continued Please stand clear before the countdown completes. DimStation Quickstart...
Page 18 9 Zero Height continued Zero height has been set. If you used the calibration object, remove it from the base. Touch the checkmark to continue. 10 Set the Scan Zone The Scan Zone is the area in which DimStation looks for and dimensions items.
Page 19 11 Complete setup Touch the checkmark to begin using your QubeVu DimStation. 12 Confirm calibration Test whether your DimStation is properly calibrated by placing the calibration object on the base or scale and checking the displayed dimensions. Dimensions should be: Length: 14.0 inches...
Page 20 • Never modify or attempt to repair or replacement charges. repair your unit. Service must be performed only by Postea personnel. • Handle cables and cable connectors with care. Never use damaged power cords and plugs or loose electrical sockets, or touch the power cord with wet hands.
Page 21 This introduction is not intended as a replacement for complete documentation. Please refer to the QubeVu Manager Guide for a complete guide to the tools. The latest version of the Manager Guide, along with all other product documentation, can be downloaded from Postea at postea.com/downloads. Define QubeVu on your Network QubeVu Manager is accessed via QubeVu’s IP address over a wired Ethernet connection.