Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Ferroli BLUEHELIX B 35
- Page 1 BLUEHELIX B 35 IT ISTRUZIONE PER L’USO L'INSTALLAZIONE E LA MANUTENZIONE ES INSTRUCCIONES DE USO, INSTALACIÓN Y MANTENIMIENTO TR KULLANMA, KURULUM VE BAK M TALIMATLAR EN INSTRUCTIONS FOR USE, INSTALLATION AND MAINTENANCE FR INSTRUCTIONS D'UTILISATION, D'INSTALLATION ET D'ENTRETIEN...
-
Page 2: General Warnings
“d2” fig. 2 Domestic hot water (DHW) “d1“ 2. OPERATING INSTRUCTIONS 2.1 Introduction BLUEHELIX B 35 premix condensing heat exchanger in steel partially pro- tected place fig. 3 The boiler is arranged for connection to an external hot water tank (op- Fault tional). - Page 3 Boiler electrically powered 2.4 Adjustments Switch on the power to the boiler. Summer/Winter Switchover summer/winter summer/winter Heating temperature adjustment fig. 5 - Switching on / Software version fig. 9 DHW temperature adjustment fig. 6 - Venting cycle Switching the boiler off and on on/off fig.
-
Page 4: Installation
Press the heating buttons (detail 3 - fig. 1) to access parallel curve offset; the display 3. INSTALLATION shows "OF" flashing. Use the DHW buttons (detail 1 - fig. 1) to adjust the parallel curve 3.1 General Instructions offset according to the characteristic (fig. 11). BOILER INSTALLATION MUST ONLY BE PERFORMED BY QUALIFIED PERSON- Press the reset button (detail 6 - fig. - Page 5 Connection to a storage tank for domestic hot water production Accessing the electrical terminal block The unit's electronic board is arranged for managing an external storage tank for domes- The electrical terminal block (fig. 15) can be accessed after removing the front panel (*** tic hot water production.
-
Page 6: Air Inlet
Connection with separate pipes Table. 6 - Accessories Losses in m Fume exhaust inlet Vertical Horizontal PIPE 1 m M/F 1KWMA83W BEND 45° M/F 1KWMA65W 90° M/F 1KWMA01W PIPE SECTION with test point 1KWMA70W Ø 80 TERMINAL air, wall 1KWMA85A fumes, wall with antiwind 1KWMA86A FLUE Split air/fumes 80/80... - Page 7 Configuration of flues Air inlet = / Fume outlet = Table. 7 - Connection with coaxial pipes Left outlets 041001X0 Rear outlets 041001X0 Right outlets 1KWMA64W 041001X0...
- Page 8 Table. 8 - Connection with separate pipes Left outlets Rear outlets Right outlets...
-
Page 9: Condensate Drain Connection
IMPORTANT - THE ROOM MUST BE PROVIDED WITH APPROPRIATE VENTILATION If the boiler is to be connected BLUEHELIX B 35 to a collective flue or a single flue with natural draught, the flue or chimney must be expressly designed by professionally qual- ified technical personnel in conformity with the current regulations and be suitable for sealed chamber units equipped with fan. - Page 10 TEST mode activation 4.3 Maintenance Press the heating buttons (details 3 and 4 - fig. 1) together for 5 seconds to activate the Opening the front panel TEST mode. The boiler lights at the maximum heating power set as described in the fol- To open the boiler casing pull the panel outwards and release it (see fig.
-
Page 11: Technical Data And Characteristics
4.4 Troubleshooting Fault Fault Possible cause Cure code Diagnostics No system H O circulation Check the circulating pump In case of operation faults or problems, the display flashes and the fault identification Exchanger protection activa- code appears. tion. Air in the system Vent the system There are faults that cause permanent shutdown (marked with the letter “A”): to restore Heating sensor fault... - Page 12 fig. 29 - Top view (AIR INLET = / FUME OUTLET = 5.2 Water circuit fig. 27 - Side view 50 50 fig. 30 - Water circuit fig. 28 - Rear view...
-
Page 13: Technical Data Table
Q [l/h] Max. gas delivery G20 fig. 31 - Circulating pump head / Pressure losses BLUEHELIX B 35 Min. gas delivery G20 0.71 A = Boiler pressure losses - B = Circulating pump min. speed - C = Circulating pump max. - Page 15 5.5 Wiring diagram fig. 32 - Wiring diagram Attention: Remove the jumper on the terminal block before connecting the room thermostat or remote timer control.