Advertisement
Quick Links
Installation Instructions
Models CAB2-BD/-RD and CAB3-BD/-RD
Medium and Large Enclosure Doors
INTRODUCTION
PRE-INSTALLATION
P/N 315-033008-8
The Models CAB2-BD/-RD and CAB3-BD/-RD Enclosure Doors from Siemens
Industry, Inc., are used with the CAB2-BB/-RB and CAB3-BB/-RB Enclosure
Backboxes. Two doors, an outer and an inner, are required for each enclosure. The
CAB2-BD and CAB3-BD outer and inner doors are black; the CAB2-RD and CAB3-RD
outer doors are red and inner doors are black.
The outer door consists of the door frame and either two or three removable panels,
depending on the enclosure size (two for the CAB2 and three for the CAB3). Each
removable panel is secured to the door with 10-32 nuts. The removable panels may
be clear (OD-LP), blank (OD-BP/-R), or vented (OD-GP/-R) depending on the applica-
tion. The OD-BP-R and OD-GP-R panels are red. The outer door is attached to the
backbox by hinge pins and secured to the backbox by keyed latch.
The inner door has two or three openings in it for the installation of an operator
interface and other modules. There are eight threaded studs around each opening on
the inner door. These threaded studs allow equipment installation on the door. The
equipment is secured by 10-32 nuts. The inner door is permanently hinged left, is
attached to the backbox by hinge pins, and is secured to the backbox by a ¼ turn
fastener or a 10-32 x 1/2" screw (user provided), if desired.
CAB2-BD/-RD and CAB3-BD/-RD Enclosure Doors are for indoor use only in dry
environments.
Outer Door:
Determine the direction that the outer door is to open. If the door is to open to the
left, no further action is required. If the door is to open to the right, the hinges must
be moved to the right side of the backbox and the outer door lock must be moved to
the left side of the outer door. (See page 2.)
Inner Door:
The handle for the inner door comes taped to the outside of the inner door. Remove
the tape from the handle and from the door. To insert the handle, press the handle
through the front of the opening in the inner door. It will snap into place. (Refer to
Figure 1.)
Siemens Industry, Inc.
Building Technologies Division
Advertisement
Related Manuals for Siemens CAB2-BD/-RD
Summary of Contents for Siemens CAB2-BD/-RD
- Page 1 ¼ turn fastener or a 10-32 x 1/2” screw (user provided), if desired. CAB2-BD/-RD and CAB3-BD/-RD Enclosure Doors are for indoor use only in dry environments.
-
Page 2: Installation
Remove the upper door hinge, turn the hinge upside down, and install on the right side of the backbox. (Refer to Figure 2.) OUTER DOOR HINGE Figure 2 Outer Door Hinge Revesal Repeat the above procedure for the lower door hinge. Siemens Industry, Inc. P/N 315-033008-8 Building Technologies Division... - Page 3 Reinstall the lock(s) on the left side of the door. Reinstall the plug(s) on the right side of the door. PLUG LOCK LOCK DOOR Figure 4 Moving The Door Lock(s) And Plug(s) Siemens Industry, Inc. P/N 315-033008-8 Building Technologies Division...
- Page 4 10-32 nuts. (Refer to Table 1 and Figure 7 .) Models LVM and FMT, one module width each, mount to the inner door. No other modules (PSC-12/PSX-12/CC-5/CC-2) may be located behind these modules. l a t l l u Siemens Industry, Inc. P/N 315-033008-8 Building Technologies Division...
- Page 5 Insert the hinge pins on the outer door in the hinges on the backbox. Install clear, blank, or vented removable panel(s) as required and secure with 10-32 nuts. (Refer to Table 2 and Figure 8.) Siemens Industry, Inc. P/N 315-033008-8 Building Technologies Division...
- Page 6 OD-LP OD-GP/-R CAB2 OUTER DOOR OD-BP/-R CAB3 OUTER DOOR Figure 8 Blank Plates For CAB2 And CAB3 Outer Doors l l i r Siemens Industry, Inc. P/N 315-033008-8 Building Technologies Division...
-
Page 7: Specifications
Figure 9 Installing The 12 AWG Ground Straps On The Inner And Outer Doors COMPATIBILITY CAB2-BD/-RD inner and outer doors can be used with CAB2-BB/-RB backboxes only. CAB3-BD/-RD inner and outer doors can be used with CAB3-BB/-RB backboxes only. SPECIFICATIONS CAB2-BD/RD: 26- ”W x 1-... - Page 8 Siemens Industry, Inc. Siemens Building Technologies, Ltd. 315-033008-8 Building Technologies Division Fire Safety & Security Products Florham Park, NJ 2 Kenview Boulevard Brampton, Ontario L6T 5E4 Canada...