Hilti TE 300-A36 Manual
Hide thumbs
Also See for TE 300-A36:
- User manual (228 pages) ,
- Original operating instructions (212 pages) ,
- Manual (32 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hilti TE 300-A36
Summary of Contents for Hilti TE 300-A36
- Page 1 TE 300A36 English Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...
- Page 2 Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...
-
Page 3: Information About The Documentation
Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •... - Page 4 The type designation and serial number are printed on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information Breaker TE 300A36...
- Page 5 ▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. ▶ Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to battery pack, picking up or carrying the tool.
- Page 6 ▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height or show signs of damage. In this case, always contact your Hilti Service. ▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable location, well away from flammable materials, where it can be kept under observation and allowed to cool down.
- Page 7 ▶ Use only Hilti Li-ion batteries from the B 36 series with this product. ▶ Use only the Hilti battery chargers from the C4/36 series for these batteries.
-
Page 8: Technical Data
If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section. Items supplied Breaker, side handle, operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or online at: www.hilti.group | USA: www.hilti.com. Technical data Product data TE 300A36... -
Page 9: Preparations At The Workplace
Battery Battery operating voltage 36 V Ambient temperature −17 ℃ … 60 ℃ Storage temperature −20 ℃ … 40 ℃ Preparations at the workplace CAUTION Risk of injury by inadvertent starting! ▶ Before inserting the battery, make sure that the product is switched off. ▶... - Page 10 1. Release the side handle clamping band by turning the handle grip. 2. Slide the side handle clamping band over the chuck from the front and into the recess provided. 3. Adjust the side handle to the desired position. 4. Tighten the side handle clamping band by turning the handle grip. Removing the chuck When changing the chuck, set the function selector switch to this position: Remove the battery from the tool.
-
Page 11: Types Of Work
1. Lightly grease the connection end of the accessory tool. ◁ Use only genuine Hilti grease. Using the wrong grease can result in damage to the tool. 2. Push the accessory tool into the chuck as far as it will go (until it engages). -
Page 12: Care And Maintenance Of Cordless Tools
• Do not operate the cordless tool if signs of damage are found or if parts malfunction. Have the tool repaired by Hilti Service immediately. • After cleaning and maintenance, fit all guards or protective devices and check that they function correctly. -
Page 13: Troubleshooting
To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com... -
Page 14: Manufacturer's Warranty
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. - Page 15 Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...
- Page 16 Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...
- Page 17 Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...
- Page 18 Hilti = registered trademark of Hilti Corp., Schaan 20180411 Printed: 13.05.2019 | Doc-Nr: PUB / 5493601 / 000 / 00...