Page 1
OPERATION AND PARTS MANUAL MODEL DM15A9C CORE DRILL MOTOR & MODEL CDM2CSA DRILL RIG STAND Revision #2 (09/04/19) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Explanation Of Code In Remarks Column ....26 Suggested Spare Parts ........... 27 Nameplate and Decals........28-29 Electric Motor Assembly........30-33 Drilling Rig Assembly ......... 34-35 Cradle Assembly ..........36-37 Tools ..............38-39 PAGE 4 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 5
NOTE PAGE DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 5...
DM15A9C (electric motor) and MQ CDM2CSA (drill or the surrounding environment. rig) will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols. PAGE 6 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Multiquip for this equipment. Damage to the equipment and/or injury to user may result. DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 7...
Page 8
See Table 1. ■ NEVER allow power cord to lay in wate r. ■ NEVER stand in water while operating the core drill. PAGE 8 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 9
■ Fix damage to the core drill immediately and always information will be invaluable in the case of an replace broken parts. Replace with only MQ emergency. recommended parts. DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 9...
DM15A9C/CDM2CSA — GENERAL INFORMATION APPLICATION Threads/Adapters The MQ DM15A9C core drill is supplied with a 1-1/4" X 7 thread The MQ DM-15A9C Stationary Core Drill Motor is designed to shaft to be used specifically with the Multiquip wet drill bits. If it ever be used with the MQ CDM-2CSA Lightweight Drilling Rig .
Page 11
■ Excessive feed pressure ■ Low feed pressure ■ High steel content in material work surface ■ Large hard aggregate ■ Too much water ■ Low electric motor RPM's DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 11...
) . g o i s . n i ) h t . n i ) h t . n i ) t h Figure 1. DM15A9C Electric Motor Dimensions PAGE 12 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
) h t . n i . n i ) h t . n i ) t h . n i ) s l Figure 2 CDM2CSA Drill Stand DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 13...
NEVER! use the drill rig with this cover removed. The possibility exists of the column falling. PAGE 14 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 15
Main Shaft – Attach core drill bit to this shaft. Main shaft is 1-1/4"-7 (7 threads per inch) male. Shaft size fits most core bits from 1-1/2" through 9" diameter. DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 15...
4. Remove the wingnut located at the top of the column as shown in Figure 6. t s i e t I i r c i t p n i - Figure 6. Wingnut Removal PAGE 16 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 17
Figure 10. Securing the Adjustment Bar Figure 8. Cradle Raise/Lower Handle 9. The unit is now ready to be secured to the work surface. DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 17...
Page 18
DO NOT attempt to use this unit until the vacuum guage reads a minimum of 20 in. Hg . The possibility exists of the gasket vacuum seal being broken and the unit tipping over. PAGE 18 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 19
Different size wrenches may be NOTE required depending on type of core bit. Figure 16. Attaching the Core Bit to the Core Drill DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 19...
Page 20
Figure 18. Be sure to place worm- clamps on each end of the hose to prevent leaking. Figure 19. Connecting the Power Figure 18. Connecting the Water PAGE 20 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
The possibility exists of a core falling on equipment causing damage to the equipment or severe bodily harm even death! to work personnel. Figure 22. Floor Drilling Application DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 21...
7. Clean the drill bit with a mild cleaning solution, removing dirt and foreign matter. 6. Store the drill rig and core drill motor out of the reach of children, in a location that is moisture free. PAGE 22 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
2. Remove any dirt and dust from the motor vents 3. Store equipment in a clean dry location that is moisture free Figure 23. Clutch Adjustment/Lubrication out of the reach of children and unauthorized personnel. DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 23...
Multiquip. A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column. PAGE 26 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
DM15A9C/CDM2CSA— NAMEPLATE AND DECALS NAMEPLATE AND DECALS PAGE 28 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 29
PART NO. PART NAME QTY. REMARKS DCL700 DECAL: CAUTION CLEAN WATER CDL001 DECAL: CAUTION, OPERATION LIGHT 1 DCL704 DECAL: MODEL INFORMATION CDL002 DECAL: INSTRUCTIONS CDB001 DECAL: MQ LOGO DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 29...
DM15A9C — TOOLS TOOLS PAGE 38 —DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19)
Page 39
DM15A9C — TOOLS TOOLS PART NO. PART NAME QTY. REMARKS CD2704103 36 MM WRENCH CD290008 46 MM WRENCH CD290106 17/19 MM WRENCH DM15A9C/CDM2CSA — OPERATION AND PARTS MANUAL — REV. #2 (09/04/19) — PAGE 39...