Table Of Contents - IBM 1402 Reference Manual

SECTION 1. INTRODUCTION.
Installation Procedure
Specifications
Speed • •
1-1
1-1
1-1
1-1
SECTION 2. PREVENTIVE MAINTENANCE 2-1
SECTION 3. SERVICING PROCEDURES
Read Feed
Timing Belts
Clutched Feed Roll Drive Belt
Reader Clutch. •
Clutch Pulley Assembly.
Clutch Drive Assembly •
File Feed Clutch • •
File Feed Joggler. • •
Hopper and Picker Knives.
Card Weights
Card Guides
Brush Assembly •
Punch Feed
Timing Belts
Timing Belt Adjustments
Punch Feed Clutch •
Geneva
Hopper and Picker Knives.
Card Guides • •
Feed Rolls and Aligner Stations.
Brush Assemblies. •
Punch Unit • • •
Cam Follower Assembly •
Interposer and Interposer Link
Interposer Guide Bar •
Interposer Setup Bail.
Latch. • •
MagDet Bar Assembly
Magnet Unit
Punch • • • •
Stripper Assembly.
Transport and Stackers
Chute Blade and Selector Magnet •
Transport Rolls.
Jam
Bar •
Stacker
Stacker Joggler •
Electrical Components
Solar Cell CB •
Lamp Assembly.
Solar Assembly. •
Component Card Assembly
Permissive Make Relays
Circuit Breakers • •
PACB • •
MagDetic PA Emitter
Open Strap Contacts.
RT and PT Relay Model 3
Punch Emitter;Model
2.
Power Supplies,Model1
Power Supplies, Model 2
3-1
3-1
3-1
3-1
3-2
3-3
3-4
3-5
3-6
3-6
3-8
3-8
3-8
3-10
3-10
3-14
3-14
3-15
3-16
3-16
3-18
3-24
3-24
3-25
3-26
3-26
3-27
3-28
3-29
3-30
3-31
3-31
3-32
3-32
3-33
3-33
3-33
3-33
3-33
3-33
3-36
3-36
3-37
3-37
3-38
3-39
3-39
3-40
3-40
3-40
3-41
./. 3-41
Motors
Redesigned Punch Feed.
Card Guides
Feed Roll Timing Check •
Feed Roll Adjustments.
Aligner Station Timing Check •
Punch Feed Removals. •
SECTION 4. SERVICE AIDS
Customer Engineering Service Panel •
Punch Service Switch Panel. •
SECTION 5. SPECIAL FEATURES
51-80 Column Device
Hopper • • •
Pocket Selectors
Stackers
Punch Feed Read •
Brushes
Card Guides.
Early Read •
SECTION 6. SERVICE HINTS
Read Feed. •
Start and Run Data Flow •
Stop Data Flow
Reader Stop Lights •
Clutch Failures •
Reader Check Lights
Validity Lights •
Brush Timing •
Circuit Breaker Timing
Punch Feed. • • •
Start and Run Data Flow •
Stop Data Flow •
Punch Stop Lights •
Punch Check Lights. •
Punch Check Brushes Out of Time
Faulty Punch Registration
Dropping Punches • • • •
Multiple Punches • •
Damaged Cards or Jams in Feed
Stacker. •• • • • • •
Faulty Stacking • • • •
Card Jamming, Transport Area
SECTION 7. LOCATIONS •
SECTION 8. SPECIAL TOOLS • •
Punch Timing Rod •
Timing Mark Gage. • •
Die Card Guide • • •
Interposer Setup Bail Gage
Stepped Feed Roll Assembly Gage
Punch Unit Adjusting Plates
Read Clutch Locating Plate Gage
Punch Unit Squareness Gage
CONTENTS
3-41
3-41
3-41
3-41.1
3-41.2
3-41.5
3-41.6
4-1
4-1
4-1
5-1
5-1
5-1
5-1
5-1
5-1
5-1
5-3
5-3
6-1
6-1
6-1
6-2
6-2
6-2
6-3
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-4
6-6
6-6
6-6
6-6
6-6
7-1
8-1
8-1
8-1
8-1
8-1
8-1
8-1
'~
8~1
,