Related Manuals for ALDI FERREX FAW 40-I
Summary of Contents for ALDI FERREX FAW 40-I
- Page 1 User Manual 40 V LI-ION CORDLESS ANGLE GRINDER FAW 40-I Original instructions ID: #05007...
- Page 2 This type of software can be downloaded for free from your app store. Try it out now Just scan the QR code with your smartphone and find out more about the ALDI product you have purchased. Your ALDI Service Portal All details mentioned above can also be found in the ALDI Service Portal at www.aldi.co.uk.
-
Page 3: Table Of Contents
Contents Overview ................4 Use ..................5 Package contents/part list ..........5 General information ............6 Reading and storing the user manual ......... 6 Explanation of symbols ............6 Safety ................... 7 Proper use ..................7 Residual risks ................8 General power tool safety instructions ........ 8 Safety notes for using the grinder ........11 Device-specific safety notes .......... - Page 5 ø 22,23 max. 3 mm ø 22,23 max. 6 mm ø 22,23 DIAMANT ø 22,23...
-
Page 6: Overview
Package contents/part list Spindle lock Thread (for supplementary handle), 3 x On/Off switch Handle surface Battery holder Supplementary handle Disc guard for grinding discs Disc guard for cutting discs Spanner Clamping flange Support flange Spindle Fastening clamp Holder (for disc guard) Grinding/cutting disc* * Example illustration! Grinding/cutting discs are not included in the package contents. -
Page 7: Use
Package contents/part list Package contents/part list Spindle lock Thread (for supplementary handle), 3 x On/Off switch Handle surface Battery holder Supplementary handle Disc guard for grinding discs Disc guard for cutting discs Spanner Clamping flange Support flange Spindle Fastening clamp Holder (for disc guard) Grinding/cutting disc* * Example illustration! -
Page 8: General Information
General information General information Reading and storing the user manual This user manual accompanies this 40 V Li-Ion cordless angle grinder FAW 40-I (referred to below only as the ‘grinder’). It contains important information on safety, usage and care. Read this user manual carefully before using the grinder. Pay particular attention to the safety notes and warnings. -
Page 9: Safety
Safety Wear ear protection. Wear suitable protective gloves. Safety Proper use The grinder is designed only for private users in connection with hobby and DIY projects for the following purposes: • for dry cutting of metal and stone materials, • for dry surface grinding of small surfaces, •... -
Page 10: Residual Risks
Safety Residual risks Despite proper use, inconspicuous residual risks cannot be completely ruled out. The following risks may arise due to the design of the grinder: • projection of parts or breakage of the sanding surface, the fitted tool or the material being processed poses a risk of severe injury or blindness if the prescribed protective goggles are not worn;... - Page 11 Safety c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
- Page 12 Safety g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Power tool use and care a) Do not force the power tool. Use the correct power tool for your application.
-
Page 13: Safety Notes For Using The Grinder
Safety b) Only use the rechargeable batteries designated for use in power tools. Using other rechargeable batteries may result in injury and a risk of fire. c) Keep the unused rechargeable battery away from paper clips, coins, keys, nails, screws or other small metallic objects that could bridge the contacts. - Page 14 Safety a flange, the hole diameter of the fitted tool must match the mounting diameter of the flange. Fitted tools not firmly attached to the power tool will rotate unevenly, vibrate significantly and may result in a loss of control. g) Do not use damaged fitted tools.
- Page 15 Safety a complete stop. The rotating fitted tool could come into contact with the surface of the base and you could lose control of the power tool. m) Never allow the power tool to run while you are carrying it. Your clothing could accidentally come into contact with the rotating fitted tool and the fitted tool could be driven into your body.
- Page 16 Safety etc. Ensure that the fitted tools do not kick back from the workpiece and get jammed in it. The rotating fitted tool tends to catch around corners, sharp edges or in the event of impacts. This will result in a loss of control or a kickback. e) Do not use a chain saw blade or a serrated saw blade.
- Page 17 Safety canting or jamming, which could cause it to kick back or the grinding tool to break. b) Avoid the area in front of and behind the rotating cutting disc. If you move the cutting disc away from you in the workpiece, the power tool and rotating disc can be hurled directly towards you if kickback occurs.
-
Page 18: Device-Specific Safety Notes
Safety d) Do not allow children or pregnant persons to enter the room or work area where you are sanding. e) Do not eat, drink or smoke while working. Clean your hands before you eat, drink or smoke. Do not leave any food or beverages exposed as there is a risk of dust accumulating in them. -
Page 19: Preparation
Preparation Preparation WARNING! Risk of injury! Accidentally starting the grinder may result in severe injury. − Always remove the battery from the grinder before you install/ remove accessories, etc. or before you carry out any other work on the grinder. Checking the grinder and package contents 1. -
Page 20: Installing The Supplementary Handle
Preparation Charging the rechargeable battery − To charge the battery, follow the instructions described in the user manual for the battery pack and charger used. Inserting and removing the rechargeable battery − To insert the battery, press the battery release button on the battery and slide the on the handle (see Fig. A). - Page 21 Preparation − Pay attention to the direction in which the grinding/cutting disc rotates. − Always use suitable protective gloves when handling the grinding/cutting disc. Removing the fitted grinding/cutting disc 1. Switch the grinder off and remove the battery from the battery holder 2.
-
Page 22: Adjusting And Changing The Disc Guard
Preparation 8. Hold the spindle lock down and use the spanner to tighten the clamping flange’s screw connection by turning it clockwise. 9. Ensure that the grinding/cutting disc is correctly, securely and firmly attached to the spindle. To do this, turn the grinding/cutting disc by hand and ensure that the grinding/cutting disc is properly secured and rotates. - Page 23 Preparation 5. Firmly attach the disc guard to the holder. To do this, move the lever of the fastening clamp towards the disc guard until it touches the neck of the disc guard. 6. Ensure that the disc guard is firmly attached and cannot be turned when on the holder.
-
Page 24: Approved Grinding/Cutting Discs
Preparation Approved grinding/cutting discs WARNING! Risk of injury! There is a risk of injury if you try to install the unsuitable grinding/ cutting discs or if you use the grinder with incorrect grinding/cutting discs. − Never install grinding/cutting discs that are not suited for the grinder. -
Page 25: Operation
Operation Operation WARNING! Risk of injury! Improper handling may pose a risk of injury. − WARNING! Lay down the grinder only once the spindle has come to a complete stop. − WARNING! Carry out a test run before each use and after each tool change. -
Page 26: Operating Instructions
Operation Start-up protection When the battery is inside the grinder and the On/Off switch is in the front switch position, start-up protection shall prevent the angle grinder from starting. − In this case, first switch off the On/Off switch, as described in the chapter ‘Using the grinder’. -
Page 27: After Use
Cleaning and maintenance Special instructions for rough machining − Always work at an angle of 30° to 40° to the workpiece. − Apply moderate pressure and move the grinder back and forth. After use 1. Switch the grinder on as described in the chapter ‘Using the grinder’. 2. -
Page 28: Cleaning The Grinder
Storage and transport Cleaning the grinder 1. Switch the grinder off and remove the battery from the battery holder (see Fig. A). 2. Wipe the housing of the grinder with a clean, lightly moistened cloth. 3. Clean the contacts of the rechargeable battery and the grinder with a dry, clean cloth. -
Page 29: Technical Data
Technical data Technical data Grinder information Article number: 97663 Model: FAW 40-I Model number: 5420073/5420074 Motor: 40 V Rated speed: 8,500 rpm Disc size: ∅ 125 mm Connection thread: Rechargeable battery and charger information Use the product only with Activ Energy® batteries and chargers with the following technical specifications: Suitable for Activ Energy®... - Page 30 Noise/vibration information Measured pursuant to DIN EN 60745-1/-2-3. The noise at your workplace may ex- ceed 85 dB(A); protective measures are necessary in this case (wear suitable ear protection). Noise emission: • Sound pressure level L 83 dB(A) • Sound power level L 94 dB(A) •...
-
Page 31: Disposal
Disposal WARNING! Depending on how the tool is used and the operating conditions, the following safety precautions must be taken to protect the user: − Avoid exposure to vibrations as much as possible. − Only use accessories in perfect working order. −... -
Page 32: Service Notes
Service notes Service notes • Store the grinder, the user manual and, if applicable, the accessories in the storage case. • FERREX® devices are largely maintenance-free. For notes on cleaning and maintenance, refer to the chapter “Cleaning and maintenance”. • FERREX® devices undergo strict quality controls. If, however, the functioning of the device is disrupted, send the grinder to the manufacturer as described in the chapter ‘Checking the grinder and package contents’. -
Page 33: Declaration Of Conformity
Declaration of Conformity Declaration of Conformity Conmetall Meister GmbH Oberkamper Straße 37 - 39 42349 Wuppertal Germany EC Declaration of Conformity We declare with sole responsibility, 40 V LI-ION CORDLESS ANGLE GRINDER that the product listed below … FAW 40-I 5420073 / 5420074 •... - Page 34 PRODUCED IN CHINA FOR: ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH. ALDI STORES (IRELAND) LTD.