Related Manuals for Neilsen CT0310
Summary of Contents for Neilsen CT0310
- Page 1 CONCRETE MIXER CT0310 & CT0313 ELECTRIC MOTOR INSTRUCTION MANUAL Please keep this instruction manual for future reference...
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: CONCRETE MIXER Model: CT0310 CT0313 Applicable EC Directives: EC-Machinery Directive 2006/42/EC EC- Directive of Electromagnetic Compatibility： 2014/30/EU... - Page 3 NAME OF MAIN PARTS 1. MIXING DRUM 6. 400mm H/DUTY WHEELS 2. ON/OFF SWITCH 7. MIXER BASE FRAME 3. HANDLE GRIPS 8. DRAW BAR FRAME 4. MOTOR AND GEAR BOX DRIVE 9. GEAR BOX MOUNTING FRAME 5. MOTOR COVER SHIELD 10.
- Page 4 SAFETY IMPORTANT! ！ PLEASE READ THIS SECTION CAREFULLY Your Mixer has been designed with safety in mind. However as with any type of machinery some basic rules apply: DO NOT Place your hand or hands in or around any part of the drum while it is operating! DO NOT Place any tools or instruments in or around the drum while it is operating!
- Page 5 DRESS PROPERLY Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can be caught in moving parts. Protective electrically on-conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair, preventing it from getting caught in Machinery.
- Page 6 ASSEMBLY OF CEMENT MIXER STEP1. Place the Mixer Base Frame (Ref 7) onto a Level Surface. Then fix the Base Frame to the Gear Box Mounting Frame (Ref 9) using the 4x3” (75mm) Bolts with 1xWashers and Nuts provided. The washers are shaped to fit around the contour of the Mixer Frame. Make sure all 4 Bolts are tight and secure before proceeding.
- Page 7 STEP4. Turn the assembled Frame of the Mixer on its side. Refer to diagram below. Take the Motor and Gear Box Drive unit. Lining up the 5 exposed Bolts with the 5 Holes, predrilled in the Back plate on the Gear Box Mounting Frame. Secure the Motor Gear Box, using the 5 Locking Nuts provided once secure, turn the Frame onto its upward position.
- Page 8 STEP7. Fix Tilting Handle (Ref 17) by locating the holes in the Tilting Handle Base Plate with the three Brackets on the under side of the Gear Box Mounting Frame (Refer to Diagram below). Once Holes are alined secure by using Metal Bolt (Ref 15) lock with Cottar Pin (Ref 16).
- Page 9 STEP9. Now both Cement Mixer and Cement Mixer Stand are fully assembled. You can now fit the Mixer to the stand. This is simply done by: * Laying Mixer on its Back (Ref to Fig.1) * Connect Central Pole (Ref 18) on the stand into the Tilting Handle Base Plate (Ref 17) on the underside of the cement mixer.
- Page 10 NOISE EMISSION LEVEL The Mixer has a noise emission level of 69 decibels. WIRING DIAGRAM S1 SWITCH F1 THERMAL PROBE C1 CONDENSER X1 MOTOR CONNECTOR PE EARTH TERMINAL NEUTRAL TERMINAL L 1 LIVE TERMINAL AM MOTOR RUNNING WINDING K1 RELAY WARNING Any type of electrical repair or trouble-shooting should only be performed by an appointed dealer or a properly qualified electrical repair shop.
- Page 11 ENGINE PARTS REFERENCE...
- Page 12 Ref. P.n. DESCRIPTION NOTE 3203932 NOTOR AND GEARBOX ASSEMBLY 230V-50Hz 2222010 SCREW 5739 M6X25 2207405 SEAL 55X40X7 2222014 SCREW M6X50 2236552 GEAR - BOX CASE HALF 2216332 ASKET 2228360 8X12 2229500 2204420 BALL BEARING 6201 2202491 GEAR 2229249 5X5X12 2202832 PINION 2215006 CASE HALVE...
- Page 13 Ref. P.n. DESCRIPTION NOTE 2223260 GASKET 2232260 2224530 WASHER Ø6X12.5 220455 BEARING 6205 2227240 SPACER WASHER E/30 2202492 GEAR 2204504 BEARING 6008 2228818 LOCATING PIN Ø6x10 2222013 M6X40 3203816 MOTOR 240V-50Hz 3203265 WASHER Ø4 2222458 SCREW TC PH M4X6 2201157 GEAR BOX DRIVE SHAFT 3203067 STOP RING...
- Page 14 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...