Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Blodgett KTT-E SERIES
Summary of Contents for Blodgett KTT-E SERIES
- Page 1 ELECTRIC TABLETOP TILTING KETTLE INSTALLATION - OPERATION - MAINTENANCE MODELS ‰ KTT-6E ‰ KTT-10E ‰ KTT-12E 42 Allen Martin Drive, Essex Junction, Vermont 05452 USA Telephone: (802) 658-6600 Fax: (802) 864-0183 www.blodgett PN S00063 Rev E (12/18) © 2018 - G.S. Blodgett Corporation...
- Page 2 Your Service Agency’s Address: Model Serial number Kettle installed by Installation checked by...
-
Page 3: Table Of Contents
TABLE OF CONTENTS IMPORTANT WARNING: Improper installa- INSTALLATION tion, adjustment, alternation, Service Connections ........... . . 2 service or maintenance can cause property damage, in- Installation Instructions . -
Page 4: Installation
Service Connections ELECTRICAL CHARACTERISTICS AMPS PER LINE MODEL 208 VAC 220 VAC 240 VAC 380 VAC 415 VAC 480 VAC 600 VAC 36.0 34.1 31.3 KTT-6E 20.8 19.7 18.1 11.4 10.4 57.6 54.6 50.0 KTT-10E KTT- 12.0 33.3 31.5 28.9 18.3 16.7 14.5... -
Page 5: Installation Instructions
Installation Instructions Immediately after unpacking, check for possible ship- 7. Wipe off excess sealant. ping damage. If the kettle is found to be damaged, save 8. A Control Box with power supply equivalent to Elec- the packaging materials and contact the carrier within 15 trical Rating of appliance should be located conve- days of delivery. -
Page 6: Operation
Introduction DESCRIPTION 4. Power is supplied to the elements through closed power contactors. Each model has a jacket of double-wall construction forming a sealed reservoir around the lower two-thirds of 5. As the temperature of water rises in the kettle reser- the kettle. -
Page 7: Operating Instructions
Operating Instructions COOKING 4. To return the kettle to the upright position, pull out the tilt lock knob and tilt the kettle upward until it locks 1. Ensure that the external electrical shut-off to kettle is in the upright position. The kettle should not move in either direction once in the upright position. -
Page 8: Maintenance
Troubleshooting GENERAL MAINTENANCE SAFETY VALVE MAINTENANCE AND TESTING No preventive maintenance is required other than adher- CAUTION ing to the Cleaning Procedure instructions. Under normal operating conditions a “try lever LOW WATER LEVEL test” should be performed every two months. Under severe service conditions, or if corro- Proper water level must be maintained within the jacket sion and/or deposits are noticed within the... -
Page 9: Tions Will Result In Satisfactory Material Safety Data Sheet - Dowfrost™ Hd Heat Transfer Fluid, Dyed
Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed... - Page 10 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 11 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 12 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 13 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 14 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 15 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 16 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 17 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...
- Page 18 Material Safety Data Sheet - Dowfrost™ HD Heat Transfer Fluid, Dyed...