Linear 831 Series Instructions

831 COMMERCIAL RECEIVER INSTRUCTIONS
MODELS:
831-S, 24 VAC & 115 VAC
• • • •
831-J, 24 VAC & 115 VAC
• • • •

PRODUCT FEATURES

831 Commercial Receivers are designed to work with most commercial door operators. The 831 is connected to the commercial
operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. The receiver
may be powered from the operator's 24 VAC transformer or from a 115 VAC circuit. There is ample room in the 831 control
box to make the proper connections. The antenna is removable and may be moved (using coaxial cable) to a new location for
better RF reception.
IMPORTANT INSTALLATION NOTES
    TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS!
WARNING
831 RECEIVERS ARE INTENDED FOR USE WITH
•
COMMERCIAL DOOR OPERATORS ONLY.
NOT USE FOR ANY OTHER PURPOSE. DO NOT
MODIFY IN ANY MANNER.
• CHECK LOCAL BUILDING AND ELECTRICAL
CODES FOR MANDATORY INSTALLATION AND
WIRING REQUIREMENTS.
CONNECT POWER CORDS ONLY TO
•
PROPERLY GROUNDED OUTLET.
PERMANENT WIRING IS REQUIRED BY CODES,
DISCONNECT POWER AT FUSE BOX OR CIRCUIT
BREAKER BEFORE ATTEMPTING ANY WIRING
CONNECTIONS.
• DO NOT WEAR RINGS, WATCHES OR LOOSE
CLOTHING WHILE INSTALLING OR SERVICING
GARAGE DOOR OPENERS. WEAR SAFETY
GOGGLES OR OTHER PROTECTIVE EYEWEAR.
AN UNBALANCED DOOR OR ONE THAT STICKS
•
OR BINDS MAY CAUSE INJURY OR DEATH.
ENSURE DOOR IS PROPERLY BALANCED AND
ELIMINATE ANY STICKING OR BINDING.
• YOUR GARAGE DOOR IS A LARGE MOVING
OBJECT. THE SPRINGS, PULLEYS, CABLES AND
INSTALLER: Leave this manual with your customer upon completion of the installation.
USA & Canada

For more information:

(800) 421-1587 & (800) 392-0123
(760) 438-7000
www.devancocanada.com
Toll Free FAX (800) 468-1340
or call toll free at 855-931-3334
www.linearcorp.com
READ THIS MANUAL CAREFULLY
BEFORE BEGINNING
MOUNTING HARDWARE UTILIZED TO BALANCE
ITS OPERATION ARE UNDER EXTREME TENSION
DO
AT ALL TIMES AND CAN CAUSE SERIOUS
PERSONAL INJURY, EVEN DEATH,
DISTURBED. ONLY A QUALIFIED SERVICE
PERSON SHOULD MOVE, LOOSEN OR ADJUST
DOOR SPRINGS OR HARDWARE.
• LOCATE CONTROL PUSHBUTTONS
A
SIGHT OF THE DOOR AND AWAY FROM THE
IF
MOVING PARTS OF THE DOOR.
ENTRAPMENT WARNING LABEL NEXT TO THE
CONTROL PUSHBUTTON IN A PROMINENT
LOCATION.
REMOVE ALL ROPES AND REMOVE OR MAKE
•
INOPERATIVE ALL LOCKS CONNECTED TO THE
GARAGE DOOR.
• T H E I M P O RT AN T S A F E G U AR D S
INSTRUCTIONS IN THIS MANUAL CANNOT
COVER ALL POSSIBLE CONDITIONS
SITUATIONS. IT MUST BE UNDERSTOOD THAT
COMMON SENSE AND CAUTION MUST BE
EXERCISED BY THE PERSON(S) INSTALLING,
MAINTAI NING AND OPERATING
EQUIPMENT.
831 COMMERCIAL RECEIVER WIRING INSTRUCTIONS
   
    
 
   
      
The 831 receiver functions as a 3-button station. Three sets of isolated contacts are provided; normally open contacts for the
OPEN PUSHBUTTON (terminals #3 & #4); normally open contacts for the CLOSE PUSHBUTTON (terminals #5 & #6);
normally closed contacts for the STOP PUSHBUTTON (terminals #7 & #8). For special STOP circuit applications,
normally open contacts (terminals #8 & #9)
are available. Refer to Figure 1.
Typical 4-wire 3-button stations are wired as
shown in Figure 2. Number 18 gauge wire or
heavier must be used for wiring the control
stations and the 831 receiver to the door
operator. Smaller gauge wire may cause
operational problems,
multiple 3-button stations are used.
typical installations the 831 receiver is
mounted near the door operator, away from
any high voltage conduits or steel support beams.
For wiring, follow the steps below and refer to
Figure 3.
In the 831 receiver, connect STOP
•
terminal #7 to CLOSE terminal #6 and to
OPEN terminal #4. Use short lengths of
18 gauge wire.
In the door operator control panel, locate
•
the wire connecting the door operator to
the 3-button station COMMON. Note its
IF
location and remove. Reconnect this wire
to terminal #8 in the 831 receiver.
• In the 831 receiver connect terminal #7
WITHIN
to the terminal in the door operator
control panel identified above.
INSTALL
• In the 831 receiver connect terminal #5 to the CLOSE pushbutton terminal in the door operator control panel.
In the 831 receiver connect terminal #3 to the OPEN pushbutton terminal in the door operator control panel..
•
Finish the wiring by connecting the 24 VAC to terminals #1 and #2 in the 831 receiver.
•
AN D
FOR 115 VAC UNIT ONLY: If the 831 receiver was ordered for 115 VAC operation it has a transformer mounted on the
circuit board. Connect 115 VAC to terminals #1 and #2. High voltage wires must be routed in a separate conduit from the
AND
low voltage wires.
BEFORE APPLYING POWER, CHECK ALL CONNECTIONS AND INSTALL THE ANTENNA.
THIS
   
   
      
IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY.
FOLLOW LOCAL BUILDING AND ELECTRICAL CODES.
DISCONNECT POWER TO RECEIVER AND DOOR OPENER BEFORE WIRING
PERMANENTLY TO PREVENT ELECTROCUTION.
105113
RADIO RECEIVER TERMINAL STRIP
CAUTION
24 VOLTS
AC ONLY
1 2 3 4 5 6
especially when
For
POWER OPEN CLOSE
Figure 1
COMMERCIAL
OPERATOR
STOP COM OPEN CLOSE
105113
DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS
PROPER ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE
MANUFACTURER OF YOUR OPERATOR FOR MORE DETAILS.
Page 2 of 4
WALL PUSHBUTTON STATION
OPEN
7 8 9
CLOSE
STOP
STOP
Figure 2
WALL PUSH −
831
BUTTON STATION
RECEIVER
OPEN
1 2 3 4 5 6 7 8 9
CLOSE
STOP
Figure 3
P/N 190-104780 REV D