Advertisement
AC power cord
CD u and the PRESET
TUNING 3 button have a
tactile dot.
A
Spacer
Template
Mounting screw
Installing the Unit
Cord clamp
Under a Cabinet
(See Fig. A)
The unit can be installed without the spacer.
1
Mark the position of the 4 holes by using the
supplied template. Use a drill to make the
holes (size 6.5 mm dia.,
A- )
2
When the cabinet door overhangs the shelf
and obstructs the unit, you can adjust the
unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you can
adjust the height in 4 steps (H••L) by
turning the spacer counterclockwise. (See
Fig. A- )
3
Install the unit with the supplied mounting
screws. (See Fig. A- )
Cautions
• Since the unit is very heavy, be careful when
installing the unit.
• You need two people to install the unit.
• Be careful with the tools you use when installing
the unit.
• Be sure that the cabinet is sturdy enough to support
the weight of the unit.
• To reduce the risk of fire, do not place any heating
or cooking appliance beneath this unit.
• Install the unit so that its AC power cord can be
connected directly to a wall outlet. Do not use a
converter or extension cord.
• Be sure that the AC power cord has no slack when
using the unit, since the cord acts as an FM wire
antenna. If the AC power cord has some slack,
wind it up to the cord hook until the cord has no
slack.
• The unit has a built-in ferrite bar antenna for AM
radio reception. Check the condition of AM
reception before fixing in position.
• Install the unit as far as possible from a source of
noise. (for example, refrigerator, microwave oven,
fluorescent lamp, etc.)
• This unit is not waterproof. The unit should be
installed where it will not be exposed to splashing
water, which could damage the unit.
• To reduce the risk of fire or electric shock, do not
touch the AC power cord with wet hands.
• Never place objects between the top of the unit and
the bottom of the cabinet. This could cause the unit
to fall.
Setting the Clock
1
Plug in the clock radio.
The display will flash "AM 12:00".
2
Press CLOCK for a few seconds.
You will hear a beep and the hour will start to
flash in the display.
3
Press TUNE/TRACK/TIME SET + or
– until the correct hour appears in the
display.
4
Press CLOCK once.
The minute will flash.
L (Low)
Dot
5
Repeat steps 3 and 4 to set the minute.
After setting the minute, press CLOCK to start
the counting of the seconds, and you will hear two
short beeps.
• To set the current time rapidly, hold down
TUNE/TRACK/TIME SET + or –.
• 12-hour system: "AM 12:00" = midnight
• In step 5, when you press CLOCK after the minute
setting to activate the clock, the seconds start
counting from zero.
To change the display to the
daylight saving time (summer
time) indication
Press D.S.T.•SUMMER T..
"
" is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
D.S.T.•SUMMER T. again.
Playing a CD
An 8 cm (3-inch) CD can be played without an
adaptor.
1
Press OPEN/CLOSE Z and place a CD
on the disc tray.
9
/
inch). (See Fig.
32
2
Press OPEN/CLOSE Z to close the disc
tray.
3
Press CD u.
Track "01" appears in the display.
The player plays all the tracks once.
4
Adjust volume using VOLUME.
To
Press
Pause
CD u
Resume play after
CD u again
pause
Locate the beginning
.**
of the current
track (AMS*)
Locate the next
>**
track (AMS)
Go back at high speed
Hold down .**
Go forward at high
Hold down >**
speed
Locate the previous
. repeatedly**
track (AMS)
Locate the succeeding
> repeatedly**
track (AMS)
Stop play
x
* AMS = Automatic Music Sensor
**These operations are possible during both play and
pause.
• This player cannot play CD-R/RW.
Note on DualDiscs
A DualDisc is a two sided disc product which mates
DVD recorded material on one side with digital audio
material on the other side. However, since the audio
material side does not conform to the Compact Disc
(CD) standard, playback on this product is not
guaranteed.
Music discs encoded with
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with copyright
protection technologies are marketed by some record
companies. Please be aware that among those discs,
there are some that do not conform to the CD standard
and may not be playable by this product.
To handle compact discs
Correct
Handle the disc
by its edge.
Incorrect
Do not touch the
surface.
Do not stick paper or
tape nor write
anything on the
surface.
Notes
• If you press CD u when there is no disc in the
CD compartment, "00" flashes for a few seconds
on the display and the unit turns off automatically.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to
do so may damage the unit. Do not use such discs.
Various Modes of CD
Preset Tuning
You can preset 10 stations in FM (5 stations in FM1,
Playback
5 stations in FM2) and 5 stations in AM.
You can play tracks repeatedly or in random order.
Presetting a Station
Press CD PLAY MODE.
Example: To preset FM90 MHz onto preset
Each press changes the play mode as follows:
1
Press RADIO ON•BAND to turn on the
Display
Play
radio.
indication
mode
2
Press RADIO ON•BAND to select FM2.
none
(normal play)
<
3
Tune in to the station on FM90 MHz (See
All the tracks are played once.
"Manual Tuning").
m
4
Hold down the PRESET TUNING
"REP 1"
(single repeat)
button 2 until you hear two short beeps.
A single track is played repeatedly.
m
"REP ALL"
(all repeat)
All the tracks are played repeatedly.
m
"SHUFFLE"
(shuffle play)
The display shows the frequency for a few seconds
All the tracks are played once
and then changes back to the current time.
in random order.
m
To change a preset station
"SHUFFLE REP" (shuffle repeat)
Tune in manually to the station you want to store and
All the tracks are played repeatedly
hold down the PRESET TUNING buttons (1-5) until
in random order.
you hear two short beeps. The previously stored
station will be replaced by the new one.
Tuning in to a preset station
1
Press RADIO ON•BAND to turn on the
Playing the Radio
radio.
2
Press RADIO ON•BAND to select the
Manual Tuning
band.
1
Press RADIO ON•BAND to turn on the
3
Press the PRESET TUNING button
radio.
lightly where the desired station is stored.
"RADIO" appears in the display.
4
Adjust the volume using VOLUME.
The display shows the band and frequency for a
few seconds and then changes back to the current
After a few seconds, the display returns to the
time.
current time but the preset button number remains.
2
Press RADIO ON•BAND repeatedly to
select the desired band.
Note
When the PRESET TUNING buttons (1-5) are
Each press changes the band as follows:
pressed lightly, the radio station that is preset will be
selected. When they are pressed for a while, the
station that is on will be newly preset.
Useful Functions
* When using FM1 or FM2 preset mode, you may
listen to the radio on either mode
To Obtain Powerful Bass
(See "Preset Tuning").
Switch MEGA BASS to ON.
3
Use TUNE/TRACK/TIME SET + or –
The "MEGA BASS" system produces a powerful bass
to tune in to the desired station.
sound.
The FM channel step is set to 0.1 MHz and the
AM channel step is set to 10 kHz.
Setting the Alarm
Two short beeps sound when the minimum
frequency of each band is received during
Before setting the alarm, make sure to set the clock
tuning.
(see "Setting the Clock").
4
Adjust volume using VOLUME.
To Set the Alarm Time
• To turn off the radio, press
1
Press ALARM for a few seconds.
OFF/ALARM RESET x.
• To improve radio reception
You will hear a beep and the hour will start to
FM: Extend the AC power cord fully to improve
flash in the display.
FM reception.
2
Press TUNE/TRACK/TIME SET + or
AM: When installing the unit, rotate the unit
– until the desired time appears in the
horizontally for optimum reception and then
display.
install the unit. A ferrite bar antenna is built
3
Press ALARM once.
into the unit.
The minutes starts to flash.
• To check the station being received, press
4
Repeat steps 2 and 3 to set the minute.
RADIO ON
BAND lightly. The display shows the
•
band and frequency for a few seconds and then
Two short beeps will confirm the setting,
changes back to the current time.
and the display will show the current time.
To Check the Alarm Time
Press ALARM.
The display shows the alarm time for a few seconds
and then returns to show the current time.
ALARM ON
To Set the Alarm Mode
Press ALARM ON/OFF to set the alarm.
"
" will appear in the display.
When the alarm comes on at the preset time, "
flashes in the display.
ALARM OFF
The alarm is turned off automatically after 60
minutes.
To Stop the Alarm
Press OFF/ALARM RESET x to turn off
the alarm.
The alarm will come on again at the same time the
next day.
To Cancel the Alarm
Press ALARM ON/OFF.
"
" will disappear from the display.
button 2 for FM2.
"
Advertisement
