Page 1
™ ® Installation Instructions for Harmony ™ 110CM Symphony Plus Applications ™ HCC/HMC/HCE/HME1000AHS, HCC/HMC/HCE/HME1400AHS, HCC/HMC/HCE/HME1000WHS, HCC/HMC/HCE/HME1400WHS (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained For applications using 110CM Symphony Plus and most countertop dispensers manufactured by Cornelius •...
Page 2
Chewblet Ice Machine Model Number Configurations ® 1400 Icemaker Voltage Series Condenser Application Configuration MC Maestro™ C 208-230/60/1 (icemaking head) 400 up to A Air-cooled, self-contained V Vision™ S RIDE ® Self-contained only. 454 lbs Chewblet ® W Water-cooled, self-contained H Harmony™...
Page 3
Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly External connection Ice transport tube Internal connection Front cover HARMONY and Symphony Plus • RIDE Technology self-contained...
Page 4
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine 1/2" 1/2" HARMONY and Symphony Plus • RIDE Technology self-contained...
Site preparation Prepare the installation site. Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. Installation site requirements H_C1000A/W ➊...
Dispenser preparation Prepare the dispenser. Attention! The location of the hole in the dispenser top is dependent on the type of dispenser. Be sure to follow Step 3.1 for the appropriate dispenser. Hole location - Harmony (Lancer, Cornelius or Servend), or 110CM Symphony Plus Lancer Sensation and Touchpoint Standard (Cornelius, Lancer, or Servend) 110CM Symphony Plus...
Page 7
Top preparation Agitation adjust. – CORNELIUS Cornelius models ED, DB, DF, IDC and FLAVOR FUSION • Screw 4" (102 mm) extension ➊ into bottom of shuttle actuator ➋ • Adjust the agitation timer located on the Cornelius PC board to 1 second on, 1 hour off.
Page 8
Agitation adjustments – LANCER FS SERIES Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 Main Menu Sub-Catagory FS-16 Setup Brands Per Side Major/Minor V:1 L:2 R:1 FS-16 Setup Bonus Key Setup Config Bonus Key V:1 T:F M:S B:W FS-16 Setup Soda/Plain Water Enter...
Page 9
Dispenser diverter plate overview (Installation on next page) Single Agitator P/N 307277 — Diverter plate (single agitator Cornelius dispensers and left-hand dispense chute on dual-agitator Cornelius dispensers) Dual Agitator P/N 307277 — Diverter plate (single agitator Cornelius dispensers and left-hand dispense chute on dual-agitator Cornelius dispensers) P/N 00996207 —...
Page 10
3.10 Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES GATE MOUNTING PLATE STORAGE HOPPER FLANGE EXTENDS INTO STORAGE HOPPER THROUGH GATE OPENING ICE DIVERTER ICE CHUTE COVER APPLY RTV TO THIS SURFACE TO SEAL TO HOPPER GATE MOUNTING PLATE 10-32 WASHER GASKET...
Page 11
Louvered docking assembly Install the louvered docking assembly. WARNING • Docking station must be secured in accordance with these instructions to ensure ice machine stability. • Ventilation openings in the louvered docking station should be clear of obstruction Machine stand accessory Wall bracket accessory •...
Page 12
Undercounter installation detail for 1000/1400 series Front View Top View Access panel/ door on counter ➊ 1.75" (45mm) ➌ 1.875" (48mm) 1.75" (45mm) 1000 series - 12"x16" cutout (305x407mm) ➍ 1400 series - 16"x16" cutout (407x407mm) bottom of ice machine side of ice machine CAUTION •...
Ice transport tube Install the ice transport tube. Ice transport tube installation. ➋ ➍ Hot Water 160 F (71 C) ➎ ➏ ➐ ➑ ➒ ➊ ➓ ➌ 1/4˝ (6,4mm) 1' (0,3m) Ice transport tube tips ➊ • Insulate entire length of ice transport tube •...
Internal connections Connect louvered docking assembly to ice machine. CAUTION • Plug must be accessible after final installation. • H_E1400A/W 230/50/1 requires a 20A circuit (4.00 mm wire) Air-cooled ice machines – follow steps 7.1 through 7.4. Ice transport tube Potable water line ...
Page 16
Water-cooled ice machines – follow steps 7.5 through 7.10. Cooling lines Ice transport tube • Install ice machine cooling water lines to • Slide ice machine into louvered docking louvered docking assembly assembly ➊ • Insert ice transport tube into coupling and tighten nut firmly ➋...
Page 17
7.10 Power cord Power cord • Remove twist tie • Position plate into opening and secure with supplied screw • Carefully pass plug thru opening and plug into wall outlet HARMONY and Symphony Plus • RIDE Technology self-contained...
Front cover Install front cover to ice machine. Water-cooled ice machines only Front cover installation – undercounter • Slide ice machine cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊...
Page 19
Long tube run recommendations max. 2 ft (0,6m) ➊ ➋ 1/4" (6,4mm) 1' (0,3m) ➊ • Pitch ice transport tube to allow melt water to drain towards ice machine ➋ • Secure insulated ice transport tube at least every 2 ft (0,6m) to prevent dips or traps HARMONY and Symphony Plus •...
Page 20
Horizon, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett Corporation. Chewblet, RIDE and Follett are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 00159897R08 www.follettice.com 8/15...