Page 1
X2 transceiver module with the major features identified. The X2 transceiver module connects the electrical circuitry of the system with the optical or copper network. Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA...
Page 2
The 10-Gigabit Ethernet X2 transceiver module has either a spring-loaded EMI gasket flange or a Note non-spring-loaded EMI gasket flange. Both transceiver module types are functionally identical. The X2 transceiver module product numbers and brief descriptions are provided in Table 1 Table Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 4
300 m (984.3 feet) X2-10GB-CX4 — InfiniBand — — 15 m (49.2 feet) (copper) X2-10GB-LRM 1310 62.5 220 m (722 feet) 50.0 100 m (328 feet) 50.0 220 m (722 feet) Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 5
–6.75 per lane –14.25 per in OMA (Min) lane in OMA (Min) X2-10GB-LRM 10GBASE-LR, 0.5 (Max) 0.5 (Max) 1260 to 1355 1310-nm MMF –6.5 (Min) –8.4 (Min average) and –6.4 (Min in OMA) Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 6
Noise-Limited Performance (measured at OSNR of 24 dB at 0.1-nm RBW) Optical Input –17.0 –7.0 Power Dispersion OSNR Penalty 1. At bit error rate (BER) = 10e-12 with an IEEE802.3 test pattern. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 12
Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057 Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Slide the X2 transceiver into the transceiver socket on the system module front panel until the X2 Step 5 transceiver EMI gasket flange makes contact with the system module faceplate. (See Figure 10-Gigabit Ethernet X2 transceiver modules are keyed to prevent incorrect insertion. Note Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 14
Repeat the process until the X2 transceiver is securely latched in the socket. Step 8 Reinstall the dust plug into the transceiver’s optical bore until you are ready to attach the network interface cable. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 15
Make sure that the InfiniBand cable connector is aligned with the X2 transceiver module. Figure 5 Cabling a CX4 (Copper) 10-Gigabit Ethernet X2 Transceiver Module X2 transceiver 4X InfiniBand connector CAB-INF-28G-5 Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
If you are not installing an X2 transceiver module in the empty socket, place a socket cover over the Step 4 empty socket opening and press on the cover until it snaps into place. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 18
Removing the 10-Gigabit Ethernet X2 Transceiver Module Figure 7 Removing the 10-Gigabit Ethernet X2 Transceiver Module L I N L I N L I N L I N Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Evitar la exposición a radiaciones láser y no mirar fijamente los orificios abiertos. Varning! Osynliga laserstrålar kan sändas ut från öppningen i porten när ingen kabel är ansluten. Undvik exponering för laserstrålning och titta inte in i ej täckta öppningar. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Laserprodukt av klasse 1. Aviso Produto laser de classe 1. ¡Advertencia! Producto láser Clase I. Varning! Laserprodukt av klass 1. Aviso Produto a laser de classe 1. Advarsel Klasse 1 laserprodukt. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Varning! Vid deponering hanteras produkten enligt gällande lagar och bestämmelser. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Page 22
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais. Advarsel Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
La aplicación de controles, ajustes y procedimientos distintos a los especificados puede comportar una exposición peligrosa a la radiación. Varning! Om andra kontroller eller justeringar än de angivna används, eller om andra processer än de angivna genomförs, kan skadlig strålning avges. Cisco 10-Gigabit Ethernet X2 Transceiver Modules Installation Note OL-23589-01...
Related Documentation For hardware installation and maintenance information on specific Cisco routers and switches, see the installation and configuration guide for your router or switch. For software configuration information and support, see the Cisco IOS software configuration and...
This document is to be used in conjunction with the publications documents that support your specific Cisco device. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.