GBC Ultima 65 Installation & Operation Manual
  1. Manuals
  2. Brands
  3. GBC Manuals
  4. Laminator
  5. Ultima 65
  6. Installation & operation manual

GBC Ultima 65 Installation & Operation Manual

Hide thumbs Also See for Ultima 65:

Advertisement

Table of Contents

See also: Service Manual , Instruction Manual
Ultima 65 Laminator
INSTALLATION & OPERATION MANUAL
Document Number: CBT10000 Rev A
Do not duplicate without written permission from ACCO Brands

Advertisement

Table of Contents
loading

Related Manuals for GBC Ultima 65

Summary of Contents for GBC Ultima 65

  • Page 1 Ultima 65 Laminator INSTALLATION & OPERATION MANUAL Document Number: CBT10000 Rev A Do not duplicate without written permission from ACCO Brands...
  • Page 2 ACCO Brands reserves the right to make changes to this publication and to the products described in it without notice. All specifications and information concerning products are subject to change without notice. Reference in this publication to information or products protected by copyright or patent does not convey any license under the rights of ACCO Brands or others assumes no liability arising from infringements of patents or any other rights of third parties.
  • Page 3 YOUR SAFETY, AS WELL AS THE SAFETY OF OTHERS IS them. IMPORTANT TO GBC. IN THIS INSTRUCTION MANUAL AND ON THE PRODUCT ARE IMPORTANT SAFETY MESSAGES. BEFORE YOU INSTALL OR USE...
  • Page 4 GBC Technical Service To order replacement accessories, service, parts, or an Equipment Maintenance Agreement, please contact GBC Technical Service and Support at: United States ACCO Brands GBC Technical Service and Support 4 Corporate Drive Lake Zurich, IL 60047-8997 www.gbcconnect.com 1-800-723-4000 Canada Ontario and Quebec –...

  • Page 5: Warranty

    2. Warranty TO THE EXTENT ALLOWED BY APPLICABLE LAW, Limited 90 Day Labor Warranty; USA, Mexico, and THIS WARRANTY IS IN LIEU OF ALL OTHER Canada EXPRESSED WARRANTIES. REPRESENTATIONS OR ACCO Brands USA LLC, ACCO Brands, 4 Corporate PROMISES INCONSISTENT WITH OR IN ADDITION Drive, Lake Zurich, IL 60047 (in Mexico, ACCO Brands TO THIS WARRANTY ARE UNAUTHORIZED AND Mexicana,Neptuno 43, Fraccionamiento Nueva...

  • Page 6: Specifications

    41.25” (104.8cm)  Height 14” (35.6cm) 18.00” (45.7cm)  Depth 21” (53.3cm) 26.25” (66.7cm)  Weight 111lbs (50.3kgs) 116 lbs (52.6kgs) Electrical Requirements Electrical Requirements • Voltage • 120V, 60Hz • Receptacle • NEMA 5-15R Figure 1. Ultima 65 Dimensions...
  • Page 7 FCC Class B Notice Disposal This device complies with Part 15 of the FCC Rules. At the end of its useful life, your product is Operation is subject to the following two conditions: considered to be Waste Electrical and Electronic ...

  • Page 8: Installation

    WARNING: Do not apply cleaning fluids or solvents to the rollers. Disconnect the plug from the receptacle and contact GBC Technical Service when one or more of the WARNING: Do not attempt to laminate following has occurred. adhesives marked ‘Flammable’.

  • Page 9: Feature Guide

    5. Feature Guide i. READY – Machine is ready to use when machine beeps and the  Icon LED turns GREEN. ii. WARM-UP – Machine is warming up when the  Icon LED is AMBER. iii. STANDBY – When icon is illuminated AMBER, machine is in Standby mode.
  • Page 10 Figure 8 moved by loosening the knob and sliding the guide to the desired position and then tightening the M. FILM ROLL SUPPLY: The Ultima 65 can use both EZ knob. Load and Standard roll laminating film (figure 8). Figure 9 N.

  • Page 11: Operation

    7. Operation FILM LOADING CAUTION: the following procedure is performed while the laminator is hot. Use extreme caution. TIP: Film loading is easiest when machine is in a Ready State or while warming up. Step 1: Lift Safety Shield and lower feed table by Figure 10 pushing down on table latches (Fig.

  • Page 12: Clearing A Jam

    Note: Continuously feeding similar size media in Loading Standard Film on Film Shaft the same location will create a wear spot. Mixing up the feeding location will give heat rollers longer life. CLEARING A JAM Film jams may occur if the laminator is not positioned to allow exiting film to drop freely to the floor.

  • Page 13: Troubleshooting

    reposition an item once the rollers have Only one roll of film is used. The top grasped it. and bottom rolls must be used for  problem free lamination. Do not stop the laminator before an item has One or both rolls of film are allowed to completely exited the rear of the laminator.
  • Page 14 on media and film (Orange Peel) Confirm proper film thickness selected Allow machine to cool Media and film have little Film is too hot when exiting the pull Slow down the laminator square patterns on the output rollers on the back of the machine. (Checker boarding) Common on longer lamination runs.

Table of Contents