Page 1
Ver. 1 SERVICE MANUAL MODEL E1K E1C DN-F450R SOLID STATE RECORDER • For purposes of improvement, specifi cations and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 3
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
TECHNICAL SPECIFICATIONS n Digital audio system n Supplied accessories • Owner’s manual • System SOLID STATE • AC adaptor • Compatible SD card SD/SDHC card • AC adaptor cord holder • Recording format • Screw for fi xing an AC adaptor MPEG1 Layer III audio cord holder compression...
Page 5
DISASSEMBLY • Disassemble in order of the arrow of the fi gure of following fl ow. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling" it. •...
Page 6
1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Remove the screws. View from bottom (2) Disconnect the connector wires and FFC cable, then remove the screws. CY041 FFC cable CX061 Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in FRONT PANEL ASSY.
2. MAIN UNIT Proceeding : TOP COVER MAIN UNIT → (1) Disconnect the connector wires and FFC cable, then remove the screws. MAIN UNIT CX061 CY041 CY051 FFC cable 3. I/O POWER UNIT Proceeding : TOP COVER MAIN UNIT I/O POWER UNIT →...
Page 8
SERVICE MODE Power switch to turn on while pressing both buttons 1 / 3 (PLAY/PAUSE)and DISPLAY at the same time. The following menus are displayed. "01 Light Check" "02 Key Check" "03 Heat Run" "04 Factory Def" The menu is selected with jog wheel. Press the Jog dial on the selected mode.
Page 9
(9) Press the 20 (STOP/CUE) button to exit the menu mode. NOTE: Please DO NOT touch and DO NOT disconnect power while the unit is being updated. If the power is turned off accidentally while the unit is being updated, the DN-F450R may not start up.
TROUBLE SHOOTING 1. MAIN PWB UNIT 1.1. Reset is not cancelled Check soldering. Check power supply turning on and the reset timing. • [IC404] N.G. b +3.3V_CPU and u-com reset : 200ms or more • [IC403] b u-com reset[TPF506] > System reset[PRST#] •...
Page 11
2. POWER PWB 2.1. The power cannot be turned on (Substrate Name : 8U-210088) Check parts. • ZD101 UDZS128 Check power supply from AC adapter. • TR101 RZR025 • TPF103 (+5V) • C101 10u/50V N.G. • C104 100u/16V and the surrounding constant. O.K.
Page 12
2.2. DISPLAY(OLED) does not display Check parts and the control signal. • TR701 KRC102S • TR702 KRA102C N.G. Check power supply for OLED. • L705 22uH • [TPF762] +12V • TR705 RHK003 and the surrounding constant. [Control signal ] • Check that Gate of TR701 becomes Hi. O.K.
Page 13
3. AUDIO UNIT( Analog 3.1. Analog audio doesn't output Check CODEC output. • [IC405]38.39.40.41pin Check parts (surrounding) and soldering. • [IC405] N.G. b When setting Fs Ref = +24dB, and the surrounding constant. 1kHz 0dBFS playback is 1Vrms. O.K. Check output of AUDIO UNIT. Check parts (surrounding) and soldering.
Page 14
3.2. Analog audio doesn't input Check input level to fi rst stage amp. Check parts (surrounding) and soldering. b When setting Fs Ref=24dB at the reference input N.G. Bal : First stage π type ATT constant level : Unbal : [IC204] constant to input : [IC203 input] 0.775Vrms and surrounding constant.
Page 30
WIRING DIAGRAM DC POWER IN JK301 I/O,POWER UNIT 8U-210088-1 CW051 CW121 CW301 CX051 CY121 CX301 5PIN 12PIN 25PIN CW051 (FFC) (FFC) CY051 CY121 CY301 CX401 6PIN CW061 (BOAD IN) MAIN UNIT 8U-310043-1 4PIN CW041 CW401 CY041 40PIN (FFC) CX061 CY401 CX041 HP UNIT PANEL UNIT 8U-310043-2...
Page 31
EXPLODED VIEW 002D 020D 008G P2-1 P1-1 910G 014B 912G 902G 002G 020G 004G P1-2 P2-2 018B Z-001 026B 002B 028B P2-3 008B 006B P1-3 012B WARNING: 016B Parts marked with this symbol have critical characteristics. 010B Use ONLY replacement parts recommended by the manufacturer.
Page 32
PARTS LIST OF EXPLODED VIEW Ref. No. Part No. Part Name Remarks Q'ty ★ Z-002 CR2032 (SANYO) zParts for which "nsp" is indicated on this table cannot be supplied. zP.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. zPart indicated with the mark "...
Page 33
PACKING VIEW 002T 004T Z-003 CW005 CW004 006T CW002 022T 004S 014T 010S 008S 006S 002S PARTS LIST OF PACKING & ACCESSORIES zParts for which "nsp" is indicated on this table cannot be supplied. zPart indicated with the mark " ★ " is not illustrated in the exploded view. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Page 34
Ref. No. Part No. Part Name Remarks Q'ty CW002 00MZC01002010 ! MAINS CORD U CW002 00MZC01003010 ! MAINS CORD EU CW004 CA-3020-180-B04-A03 CW005 2P PIN CORD Z-003 00MAA90005163 !AC ADAPTER(5V 1.5A)
Page 35
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5S72631P200FP (MAIN :IC505)
Page 46
M29W640GB70NA6E (MAIN : IC501) V CC V PP /WP A0-A21 DQ0-DQ14 DQ15A–1 M29W640GT M29W640GB BYTE M29W640GH M29W640GL V SS M29W640GB70NA6E Pin Description Name Description Direction A0-A21 Address Inputs Inputs DQ0-DQ7 Data Inputs/Outputs Inputs/Outputs DQ8-DQ14 Data Inputs/Outputs Inputs/Outputs DQ15A–1 (or DQ15) Data Input/Output or Address Input (or Data Input/Output) Inputs/Outputs Chip Enable...
Page 55
UPD4721GS-GJG +C (MAIN :IC102) +10 V +3.3 V – +5 V – –10 V STBY – Note 4 OUT1 OUT2 OUT1 5.5 k OUT2 5.5 k Note 1. V and V are output pins stepped up internally. These pins should not be loaded directly. 2.
Page 56
BD9851EFV (I/O POWER : IC101) BD9851EFV Pin Function...
Page 59
3. BATTERY CR2032 (SANYO) The exchange of the battery (IEC60065, UL60065). CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Page 60
PARTS LIST OF P.W.B. UNIT zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A.