1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. WS-X45-SUP6L-E
  6. Installation and configuration note

Cisco WS-X45-SUP6L-E Installation And Configuration Note

Hide thumbs
Table of Contents

Advertisement

Quick Links

Installation and Configuration Note for the Cisco
Catalyst 4500 E-Series Supervisor Engine 6L-E
Product Numbers: WS-X45-SUP6L-E= Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E, MEM-X45-512MB-LE,
MEM-X45-1GB-LE
This publication describes how to install and verify the operation of the Catalyst 4500 E-series
Supervisor Engine 6L-E. Refer to the software configuration guide for your switch for configuration
information for the supervisor engines and switching modules.
Note
Catalyst 4500 E-series switching modules require an E-Series Supervisor Engine running a software
image compatible with that supervisor engine. Refer to your switch's release notes for compatibility
information.
Contents
This document contains these sections:
•
•
•
•
•
•
•
•
•
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2009 Cisco Systems, Inc. All rights reserved.

Advertisement

Table of Contents
loading

Related Manuals for Cisco WS-X45-SUP6L-E

Summary of Contents for Cisco WS-X45-SUP6L-E

  • Page 1: Table Of Contents

    Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E Product Numbers: WS-X45-SUP6L-E= Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E, MEM-X45-512MB-LE, MEM-X45-1GB-LE This publication describes how to install and verify the operation of the Catalyst 4500 E-series Supervisor Engine 6L-E.

  • Page 2: Safety Overview

    à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 3 Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 4 Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 5 Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 6 Safety Overview Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 7: Supervisor Engine 6L-E

    Supervisor Engine 6L-E Supervisor Engine 6L-E This section describes the Catalyst 4500 E-series Supervisor Engine 6L-E (WS-X45-SUP6L-E). See Figure 1. This supervisor engine provides IPv6 data path and data control for all Layer 2 network interfaces, and provides 10-Gigabit Ethernet interfaces for uplinks.
  • Page 8 Broadcast suppression on a per-port basis Multicast suppression on a per-port basis • Unicast suppression on a per-port basis • EtherChannel at 10/100/1000 Mbps and 10Gbps • Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 9 System boot or diagnostic test is in progress. Module is disabled. UTILIZATION Green 1–100% If the switch is operational, this display indicates the current traffic load over the backplane (as an approximate percentage). Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 10 Gigabit Ethernet SFP Uplink Ports If you want to use SFPs instead of X2s as your uplink transceivers, you can use the Cisco TwinGig converter modules already provided in the X2 slots. Installation documentation for Cisco TwinGig converter modules can be found at: http://www.cisco.com/en/US/docs/switches/lan/catalyst3750e_3560e/hardware/install/notes/1757202.html...
  • Page 11 Network Example with Routing Protocols Enabled Ethernet management Switch port Network cloud Network ports Network cloud The specific implementation of Ethernet management port depends on the redundancy model you are applying. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 12: Port Cabling Specifications

    (the type of cabling used to transmit the signals). The distance and rate limits in this document are the IEEE-recommended maximum speeds and distances for signaling. Table 2 shows the transmission speed versus the distance. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 13 Removing the Supervisor Engine, page 17 • When installing modules in a chassis with empty slots, populate the upper empty slots first and work Note down. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 14 Handle carriers by available handles or edges only; avoid touching the printed circuit boards or • connectors. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 15: Installing The Supervisor Engine

    Align the edges of the supervisor engine carrier with the slot guides on the sides of the switch chassis, Step 6 as shown in Figure Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 16 If the module is not operational, reseat it. If the module is still not operational, contact your customer Step 3 service representative. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 17 E ˝ R IE L IN 1 0 / 1 0 0 / 1 0 E ˝ R IE L I N Ejector lever Captive installation screw Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 18: Memory Upgrade

    MEM-X45-1GB-LE. You might need to upgrade memory on the Supervisor Engine 6L-E for the following reasons: To upgrade to a new Cisco IOS feature set or release that requires additional memory. (Memory • requirements for each feature set and release are available in the release notes for that release.) To use very memory-intensive features.
  • Page 19 Handle the SODIMM by the edges only; do not touch the memory modules, pins, or traces (metal fingers Caution along the connector edge). Handle carefully. DIMMs are ESD-sensitive components and can be damaged by mishandling. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 20 L IN IN K T IV L IN IN K T IV 1 0 /1 0 0 /1 0 0 0 E ˝ R IE L IN Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 21 Step 4 edge, and there is a corresponding key on the memory slot, make sure they are oriented to seat correctly. Figure 8 Handling a DIMM Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 22 WS-C4506 (MPC8548) processor (revision 0) with 1048576K bytes of memory. Processor board ID FOX104810F8 MPC8548 CPU at 1GHz, Supervisor 6L-E Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 23: Attaching Module Interface Cables

    (around the optical-fiber openings), generating significant attenuation and reducing the optical power levels below threshold levels so that a link cannot be made. Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...
  • Page 24 Make sure that the optical connectors are clean before making the connections. Contaminated connectors Note can damage the fiber and cause data errors. Figure 12 LC Fiber-Optic Connector Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 25: Configuring Your Supervisor Engine

    Full documentation of the X2 transceiver is in the 10-Gigabit Ethernet X2 Transceiver Installation Note. You may also use Cisco TwinGig and Cisco OneX converter modules in these ports. Installation documentation for Cisco TwinGig converter modules can be found in the Installation Notes for the Cisco TwinGig Converter Module.
  • Page 26 Cisco SFP and SFP+ Transceiver Module Installation Notes. Use only Cisco SFP modules on your Cisco device. Each SFP module has an internal serial EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the SFP module meets the requirements for the device.

  • Page 27: Related Documentation

    Cisco SFP and SFP+ Transceiver Module Installation Notes Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix • Inspection and Cleaning Procedures for Fiber-Optic Connections • Installation Notes for the Cisco TwinGig Converter Module • Installation and Configuration Note for the Cisco Catalyst 4500 E-Series Supervisor Engine 6L-E OL-19334-02...

  • Page 28: Obtaining Documentation And Submitting A Service Request

    ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

This manual is also suitable for:

Mem-x45-512mb-leMem-x45-1gb-leCatalyst 4500 e supervisor engine 6l-e series

Table of Contents