Advertisement
Quick Links
Dealer Setup
& Adjustment Instructions
319 Series Single Stage Snowthrower
This Dealer Setup Instruction applies to the following units:
319 Series Snowthrowers
Mfg. No.
Description
1694382
319M, 3HP Snowthrower, Manual Start
1694383
319E, 3HP Snowthrower, Electric Start
ATTENTION SETUP PERSONNEL:
The safety warnings provided in this guide and
in the operator's manual included with the unit
contain important information that must be
obeyed when assembling, setting-up, operating, servic-
ing, transporting, or storing the unit.
These warnings are highlighted by the safety alert trian-
gle symbol shown above, which signifies that an impor-
tant safety message is being provided.
You must read, understand, and follow these warn-
ings and instructions, and use safe shop and work
practices at all times while working on or around this
unit and all other outdoor power equipment.
Sections and items denoted by the Setup sym-
bol provide the information necessary to fully
assemble, test, and prepare the units
described above for delivery to your customers.
A Quick Setup List is provided on page 3 of this
booklet to help you identify and check that the items
have been performed.
4/2003
These instructions may cover additional models
issued after their printing. Refer to the Dealer
Setup Binder Index for complete listings.
TABLE OF CONTENTS:
SAFETY RULES........................................................2
Quick Setup List.......................................................3
Unboxing and Assembly .........................................4
Fill Gas Tank.............................................................5
Auger Cable Adjustment .........................................6
Test Run....................................................................6
Simplicity Form No. 1725536-00
1
Snapper Form No. 24536
TP 300-3862-00-SW-S
Advertisement
Related Manuals for Snapper 3190E
Summary of Contents for Snapper 3190E
-
Page 1: Table Of Contents
Refer to the Dealer Setup Binder Index for complete listings. TABLE OF CONTENTS: SAFETY RULES...2 SETUP PROCEDURES Quick Setup List...3 Unboxing and Assembly ...4 Fill Gas Tank...5 Auger Cable Adjustment ...6 Test Run...6 Snapper Form No. 24536 Simplicity Form No. 1725536-00 TP 300-3862-00-SW-S... -
Page 2: Safety Rules
319 Single Stage Snowthrower Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe per- sonal injury or death to you, yourself or bystanders, or damage to property or equipment. This auger is capable of amputating hands and feet and throwing objects. -
Page 3: Setup Procedures
Quick Setup List - Page Setup Procedure Unbox & Assemble Fill Gas Tank Adjust Auger Cable Test Run 4/2003 319 Single Stage Snowthrower Steps to Perform ❏ Remove Unit From Box. ❏ Install Discharge Chute ❏ Assemble Handle Bars (Be careful not to pinch the auger cable) ❏... -
Page 4: Unboxing And Assembly
319 Single Stage Snowthrower Unboxing & Assembly 1. Using a utility knife, open the box and remove the snowthrower. IMPORTANT NOTE When removing the snowthrower from the box and unfolding the handle bars DO NOT PINCH THE AUGER CONTROL CABLE IN THE HANDLE BARS. 2. -
Page 5: Fill Gas Tank
Fill Gas Tank Fuel and Oil Mixture The snowthrower uses a two cycle engine that requires a mixture of fuel (gasoline) and oil for lubrication of engine bearings and other moving parts. The correct fuel/oil mixture ratio for the five horsepower engine is 50 to 1. -
Page 6: Auger Control Cable Adjustment
319 Single Stage Snowthrower Auger Control Cable Adjustment Inspection 1. Inspect the auger cable for kinks, wear, or frayed cable strands. Replace if worn or damaged. 2. Start the engine. 3. Engage the auger control for 5 seconds. 4. Disengage the auger control. The auger should stop in 5 seconds or less.