Summary of Contents for UTStarcom MovingMedia 2000
- Page 1 ® MovingMedia 2000 iCell CDMA2000 1X iPA 1900 MHz Translating Bi-directional Amplifier BASIC INSTALLATION GUIDE RELEASE 4.5 DRAFT 0.1 PART NUMBER NXX0306XXX Page 1 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 2 Page 2 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 3 Copyright © 2004 UTStarcom Incorporated. All rights reserved. Copyright © 2004, UTStarcom, Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior written permission from UTStarcom, Inc.
- Page 4 Chapter 1 Preface Introduction to the Installation Guide. Chapter 2 iCell System Description Describes the System components Chapter 3 iPA Physical Installation Provides mechanical installation and wiring instructions. Page 4 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
-
Page 5: Reference Documents
Internet Protocol iCell Power Amplifier Management Information Base Mobile Station (phone) Mobile Switching Center Network Element or agent Network Operations Center Object Identifier Operations & Maintenance Center Power Amplifier Page 5 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide... - Page 6 Public Switch Telephone Network PSTN Radio Frequency Short Message Service Center SMSC Simple Network Management Protocol SNMP Simple Network Timing Protocol To Be SNTP Defined Transmission Control Protocol Time Of Day MovingMedia 2000 iCell Macro with iPA Installation Guide Page 6 of 14...
- Page 7 Ethernet interface to the core network. For Macro coverage small footprint iPA Bi- directional amplifier is added to the basic BTS configuration. Figure 2-1 shows the system architecture. Figure 2-1: iCell Macro BSS using iPA Page 7 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 8 IF for signal enhancement, then up-converts to PCS band for transmission. Figure 2-2: iCell 800 MHz Pico BTS interfaced to Translating iPA 1900 MHz (3 sector Case shown using 3 iPAs) Page 8 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 9 Take the necessary precautions to minimize electrostatic damage while handling modules. Carefully remove all parts and hardware out of the packages. Carry out a full inventory before installation procedure starts. Page 9 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 10 Figure 3-1: BTS 19' Rack Mont Rear View Figure 3.2: BTS 19” Rack Mount Front View Figure 3.3: iPA Front View Figure 3.4: iPA Rear View (AC input Power) (-48v DC version also available) Page 10 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 11 Page 11 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
-
Page 12: Interface Connections
3.4.2 BTS to iPA Interface Connection Figure 3-1 illustrates the wiring diagram of the BTS and iPA for Macro coverage. Table 3-1 provides the wiring parameters. Figure 3.1: BTS and iPA wiring diagram Page 12 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide... - Page 13 1 PPS IN 1 GPS 1 PPS 363-06097-0015 Power External Source Supply AC Power Power Switching 363-02155-0002 N O T E All SMA connectors that are not connected should be terminated. Page 13 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...
- Page 14 “–“ or “–48v” and the positive (Bat. Rtn) wire to the terminal marked “+” or Bat Return. The BTS and iPA are now ready for configuration. Refer to iCell CDMA2000 1X Configuration Guide. Page 14 of 14 MovingMedia 2000 iCell Macro with iPA Installation Guide...