LG 42PM4M Owner's Manual page 34

Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to 'Real Data Mapping 1'. See page 38.
Language
Child lock
ISM Method
Set ID
Tile mode
Low power
XD Demo
1. Press the MENU button and then use the
2. Press the G G button and then use
3. Press the G G button and then use
• The adjustment range of Set ID is 1 ~ 99.
Communication Parameters
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
Command Reference List
Command Reference List
COMMAND 1 COMMAND 2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode k
14. PIP/DW
15. PIP Position
16. Treble
17. Bass
18. Balance
19. Color Temperature
20. Red adjustment
21. Green adjustment
22. Blue adjustment
23. PIP Input Select
24. Abnormal State
25. ISM Method
26. Low Power
27. Picture Size Setting
for DW mode
28. Auto Configure
29. Key
button to select the
D D / E E
button to select Set ID.
D D / E E
button to adjust Set ID to choose the desired monitor ID number.
F / G
DATA
(Hexadecimal)
k a 0 ~ 1
k b 1 ~ 9
k c 0 ~ 3
k d 0 ~ 1
k e 0 ~ 1
k f 0 ~ 64
k g 0 ~ 64
k h 0 ~ 64
k i 0 ~ 64
k j 0 ~ 64
k k 0 ~ 64
k l 0 ~ 1
m 0 ~ 1
k n 0 ~ 3
k q 0 ~ 3
k r 0 ~ 64
k s 0 ~ 64
k t 0 ~ 64
k u 0 ~ 3
k v 0 ~ 14
k w 0 ~ 14
k $ 0 ~ 14
k y 1 ~ 9
k z 0 ~ a
j p 0 ~ 3
j q 0 ~ 1
j t 0 ~oa
j u 1
m c Key code
SPECIAL menu.
• Stop bit : 1 bit
• Communication code : ASCII code
T T ransmission / Receiving Protocol ransmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j, m
* [Command 2]: To control PDP set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID '0', every con-
nected PDP set is controlled. Set ID is indicated
as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code '0x0D'
* [ ]: ASCII code 'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: Not supported function
External Control Device Setup
Language
Child lock
ISM Method
Set ID
G
Tile mode
Low power
XD Demo
Owner's Manual 35
1