Vertex Standard BH-2 Operating Manual

"BH-2" Bluetooth
When the optional BU-1 Bluetooth ® Adapter Unit is installed in the Transceiver*, you may use the BH-2 Bluetooth
Headset as a wireless link to send and receive audio to the Transceiver*.
Controls & Connections
Microphone
POWER switch
VOLUME (–) switch
Pressing this switch decrease the receiver volume level.
Press this switch while pressing and holding the PTT
switch, to decreases the microphone gain.
VOLUME ( + ) switch
Pressing this switch increase the receiver volume level.
Press this switch while pressing and holding the PTT
switch, to increases the microphone gain.
LED Indicator
Blinking Blue: When the BH-2 Bluetooth Headset is
®
correctly recognized by the transceiver.
Blinking Red: When the BH-2 Bluetooth ® Headset is
not correctly recognized by the trans-
ceiver.
Blinking Red/Blue: Battery Voltage is Low.
PTT switch
Press this key to transmit. Release this key to return to
receive (Depends on transceiver settings).
SPEAKER
Earhook
You can wear the BH-2 on your left or right ear.
Pairing
Before you can use your BH-2 for the first time, the BH-2
and the transceiver must be paired.
Refer to the Transceiver's Operating Manual for Pairing in-
structions.
Please bring the BH-2 and the Transceiver close together
when doing Pairing.
1. Make sure that the BH-2 is off.
2. Press and hold the POWER switch for five seconds, until
the LED indicator blinks red/blue alternately.
When the BH-2 is correctly recognized (Requires a 20 to 30
seconds) by the transceiver, the LED indicator will blink
blue.
LED indicator
POWER Switch
E A F 4 4 U 7 6 0
® Head Set
* Check with your Vertex Standard Dealer or Catalog for applicable models.
BH-2 is not designed to attach to a motorcycle helmet.
Specifications are subject to change without notice.
Turning ON and OFF
T T T T T o turn the o turn the BH-2 ON o turn the o turn the ON ON ON
o turn the ON
Press and hold the POWER switch for three seconds, un-
til the BH-2's LED indicator glows red, and the beeper
sounds a high pitch tone.
When the BH-2 is correctly recognized by the transceiver,
the LED indicator will blink blue.
When the BH-2 is not correctly recognized by the trans-
ceiver, the LED indicator will blink red.
T T T T T o turn the o turn the BH-2 OFF o turn the o turn the o turn the OFF OFF OFF OFF
Press and hold the POWER switch for five seconds, until
the BH-2's red LED indicator blinks rapidly, the beeper
sounds two brief tones, and the BH-2 turns off.
POWER Switch
Effective Communications Range
The communications range between the BH-2 and the
Transceiver is around 10m (33 ft).
Obstacles between the BH-2 and the Transceiver may
decreas the communications distance.
When you move out of range, the beeper sounds a low
pitch tone. When you move back into range, the beeper
sounds a high pitch tone.
Wearing the BH-2
1. Open the earhook.
®
2. Loop the earhook over your ear.
3. Press the BH-2 to your ear.
4. Adjust the flexible boom microphone
by bending the boom towards your
mouth.
For more comfort when wearing the BH-2, affix the sup-
plied sponge on the speaker and press the supplied sponge
ball onto the earhook, and adjust as necessary.
The BH-2 comes ready to fit the left ear. You may change
the BH-2 to fit the right ear in the following procedure.
1. Remove the Earhook by pushing it out with a pointed
object.
2. Insert the Earhook from the other side.
Operation
T T T T T ransmission ransmission ransmission ransmission
ransmission
Press the PTT switch to transmit, and release the switch
to return to receive (Depends on transceiver settings).
Adjusting the V Adjusting the V Adjusting the Volume level Adjusting the V Adjusting the V olume level olume level olume level olume level
Adjust the receiver audio level, using the VOLUME ( – ) or
(+) switch.When the audio level reaches the maximum
or minimun, the beeper sounds two brief tones.
VOLUME (+): Adjusts the receiver audio level upward.
VOLUME ( – ): Adjusts the receiver audio level downward.
Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting Microphone Gain Setting
Press and hold the PTT switch, while using the VOLUME
(+) or ( – ) switch to select a comfortable Microphone gain
level (Five steps). When the microphone gain reaches the
maximum or minimun, the beeper sounds a high pitch tone.
VOLUME (+): Sets the MIC gain upward.
VOLUME ( – ): Sets the MIC gain downward.
VOLUME (–) Switch
Battery
When the battery voltage becomes low, the BH-2's LED indi-
cator will blink red/blue alternately, and the beeper sounds
a low pitch tone.
If the battery has never been used, or its charge is depleted,
it may be charged by connecting to the Charger Sleeve* or
Charger Cradle*, as shown in the illustration.
Please refer to the transceiver's manual for installation of
the Charger Sleeve.
* Check with your Vertex Standard Dealer or Catalog for appli-
cable models.
1. Insert the BH-2 into the Charger Sleeve or Charger Cradle.
Note Note : If the BH-2 is inserted into the Charger Sleeve or Note Note Note
Charger Cradle while the BH-2 power supply is
"ON", it is automatically set to "sleep" mode.
When it is disconnected from the Charger Sleeve
or Charger Cradle, the BH-2 will be active again.
2. If the BH-2 is inserted correctly, the LED indicator will
glow Red. A fully discharged battery will be charged com-
pletely in 3 hours. When charging is finished, the LED
indicator will glow blue.
Example:Use the "CAB-1"
Battery saver Battery saver Battery saver Battery saver Battery saver
If there has been no signal or key button activity for 20 sec-
onds, the Battery Save automatically puts the BH-2 in "sleep"
mode, to conserve battery life.
When a signal is received or the PTT key is pressed the
BH-2 will be active again.
Refer to the Transceiver's Manual for Battery saver instructions.
Specifications
Bluetooth specification
Bluetooth profiles
Radio Frequency
Modulation method
Transmitter output power
Receiver sensitivity
Distance (open area)
Audio format
Audio frequency range
Power supply
Battery life
Button/Switch
LED indicators
PTT Switch
Operating temperature
Operating humidity
Certification
Replacement Parts
Ear hook ................. S8002323
VOLUME (+) Switch
Ear hook sponge ..... S8002325
Example:Use the "CD-40"
Ver1.2
HSP
2402 MHz - 2480 MHz
GFSK
0 dBm Class 2
<-80 dBm
32 ft (10 meters)
SBC
100 Hz - 20 kHz
Rechargeable Lithium-Polymer
6 hours
Power On/Off, Volume Up/Down, PTT
Power on: Flash blue twice
Unlink: Flash red
Link: Flash blue
Pairing: Red and Blue blinking
Battery low: Flash red and blue
Power off: Flash red 3 times
32 °F to 104 °F (0 °C to 40 °C)
5 - 90 %
FCC, CE, BQB
Speaker sponge ....... S8002324
Wind Screen ........... S8002322