Caution For Ac Mains Lead; Features - Panasonic AG-MD830E Service Manual

......
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped wijh 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only for
U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 13 amp fuse is fined in this plug.
Should the fuse need to be replaced please ensure that
the replacement fuse has a rating of 13 amps and that
it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark ~ or the BSI mark ~ on the
body of the fuse.
If
the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced.
If
you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from your
local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME THEN
THE FUSE SHOULD BE REMOVED AND THE PLUG
CUT OFF AND DISPOSED OF SAFELY. THERE IS A
DANGER OF SEVERE ELECTRICAL SHOCK IF THE
CUT OFF PLUG IS INSERTED INTO ANY 13 AMP
SOCKET.
If a new plug is to be fitted please observe the wiring
code as shown below.
If
in any doubt please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in Ihis mains lead are coloured
in accordance with the following code:
Green·and·Yellow: Earth
Blue: Neutral
Brown:
Live
FOR U.K. ONLY
If the plug supplied is not suitable for your socket
out/et, it should be cut off and appropriate one fitted.
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
• The wire which is coloured GREEN·AND-YELLOW
must be connected to the terminal in the plug which is
marked with the letter E or by the Earth symbol ~ or
coloured GREEN or GREEN-AND·YELLOW.
• The wire which is coloured BLUE must be connected
to the terminal in the plug which is marked with the
letter N or coloured BLACK.
• The wire which is coloured BROWN must be con-
nected to the terminal in the plug which is marked with
the letter L or coloured RED.
How to replace the fuse
1. Open the fuse compartment with a screwdriver.
2. Replace the fuse.
- E-2-
OPERATING INSTRUCTIONS
Features
Rotary erase head
The rotary erase head is featured to ensure cleaner
edits during editing.
Hi-Fi recording
High picture quality
Compactly designed for easy portability
Illuminated operation buttons
Repeat playback
A particular section on the tape can be continuously
played back repeatedly or played back once.
Jog and shuttle functions
The unit's jog and shuttle functions enable playback
section to be located speedily using the search dial.
Mode locking
Even when an operation button has been pressed in
error, the mode lock function prevents the unit from
performing the operation corresponding to that button.
Unrecorded blank search
The unit detects unrecorded blanks which are 5. or
more seconds in length.
Automatic high-speed VISS search
By writing the VISS (VHS Index Search System)
signals at particular scenes to be viewed, the scenes
can be easily located and played back automatically.
Audio dubbing
Audio can be added to the normal audio track during
post production editing.
Switch settings on screen menus
The unit's on-screen system enables switch settings to
be viewed on Ihe TV screen.
Auto head cleaning
This facility automatically cleans the video heads to
remove any dirt.
Pause remote control supported
Recording can be started and stopped by remote
control using the VW-RM1 which is available as an
optional accessory.
RS-232C serial interface supported
The unit can be remote-controlled from a personal
computer by mounting the AG-IA823 interface which
is available as an optional accessory.
34-pin remote control supported
The unit can be operated from a distance of 5
meters or so using the AG·A600 (an optional acces·
sory) by installing the AG·IA34 interface which is
available as an optional accessory.
-E-5 -