Salus AE10RF Installer's/User's Manual

DELETING THE REPEATER FROM THE NETWORK
Press button on
the Repeater for 10
seconds to delete the
existing network.
The button colour
changes to amber
to indicate deletion.
At this point,
you cannot cancel
the procedure.
After you have deleted the repeater from the
ZigBee network, it will need to be re-installed.
Also, if you delete the repeater, all the thermostats
connected to the repeater will lose their connection
to the network.
Product Compliance & Safety Info WARRANTY
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
SALUS North America warrants that this product will be free from any defect in materials or
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment workmanship, and shall perform in accordance with its specification, for a period of five years
generates uses and can radiate radio frequency energy and, if not
from the date of installation. SALUS North America sole liability for breach of this warranty
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
will be (at its option) to repair or replace the defective product.
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Customer Name: .............................................................................................................................
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Customer Address: ..........................................................................................................................
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
............................................................................... Post Code: ........................................................
Changes or modifications not expressly approved by the party
Tel No: ........................................................ Email: .........................................................................
responsible for compliance could void the user's authority to operate
the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
Engineers Company: .......................................................................................................................
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Tel No: ......................................................... Email: ........................................................................
This device complies with Industry Canada's licence-exempt RSSs.
Operation is subject to the following two conditions:
Instalation Date: ..............................................................................................................................
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Engineers Name: ............................................................................................................................
Le présent appareil est conforme aux CNR d'Industrie Canada
Engineers Signature: .......................................................................................................................
applicables aux appareils radio exempts de licence. L' e xploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d' e n compromettre le fonctionnement.
Warning
TECHNICAL DETAIL
These instructions are applicable to the SALUS
model stated on this instruction guide.
This product must be fitted by a competent person, and
Model
installation must comply with the guidance, standards and
regulations applicable to the city, country or state where the
Type
product is installed. Failure to comply with the requirements
of the relevant guidance, standards and regulations could
lead to injury, death or prosecution.
Function
Warning
Control
Always isolate the AC Mains supply before installing or
Indication
working on any components that require 120 V 60Hz supply.
User Interface
We hope you enjoy this product...
Operating Temperature
Storage Temperature
Frequency
Power Source
Approval
AE10RF
ZigBee Repeater
Zigbee network coordinator for Wyse.ly system
Open - Close the ZigBee network
Bi-Colour LED: RED - AMBER
Single push button
0 to 45 ºC (32ºF up to 113ºF)
-20ºC to 60ºC (-4ºF to +140ºF)
2.45 GHz
Adaptor with USB plug output (supplied)
FCC and IC
ZigBee Repeater
Models: AE10RF
I N S T A L L E R / U S E R M A N U A L
SALUS North America
850 Main Street
Redwood City
CA 94063
T: +1-650-360-1725
E: sales@salusna.com
www.salusna.com
SALUS North America is a member of the Computime Group
Maintaining a policy of continuous product
development, SALUS Controls plc reserves the right
to change specification, design and materials of
products listed in this brochure without prior notice.
For PDF Installation guide go to
www.salusna.com
00086/2 Issue Date: October 2016