Advertisement
What's in the carton?
Verify that the following items are in the shipping carton. If any items
are missing, contact your service provider:
• The CLG-8202-WW Connected Life Gateway
• The CLG-8202-WW Connected Life Gateway cradle
• Protective cover for the USB connector
• AC power adapter
• Yellow CAT 5 Ethernet cable
• Two Phillips screws
Installation instructions
The gateway can be installed in one of two ways: desktop- or wall-
mounted.
Items needed
In addition to the items provided in the gateway shipping carton, the
following additional materials are needed:
• One Phillips screwdriver
• One Ethernet cable long enough to reach from the Cisco
Connected Life Gateway to a PC or router
When mounting to a wall, the following additional materials are
needed:
• One pencil to trace the mounting holes to the wall
• Two #6 (M3.5) pan head screws
• One screwdriver
• One drill and drill bit
Wall mounting
Mounting holes
1. Turn the cradle so the mounting holes are opposite from you,
and place the cradle against the wall where you intend to mount
it.
2. While holding the cradle in place, use a pencil to trace the
mounting holes onto the wall.
3. Drill two holes into the wall where the pencil traces indicate.
4. Install the mounting screws into the wall, leaving a gap of about
½-inch between the screw head and the wall.
5. Place the cradle into position by slipping the large end of both
mounting slots over the screw heads and sliding the cradle
down until the narrow end of the mounting slots contacts the
screw shafts.
6. Continue installing the gateway by following the instructions for
Desktop mounting.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affi liates in the U.S. and other countries. To view a list of Cisco trademarks, go to
this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1110R)
© 2014 Cisco and/or its affi liates. All rights reserved
Printed in China
Desktop mounting
Allow approximately 3-5 minutes to install the gateway to stand on a
desktop.
Controller
Cradle
1. Insert the gateway into the cradle until you feel it lock into place.
2. Using a screwdriver, secure the controller to the cradle by
inserting the two screws and tightening.
3. Insert one end of an Ethernet cable into the yellow Internet port
and the other end of the cable into an Ethernet port on a router.
Note: The gateway will be connected to a router except during
initial set up when it is connected to a PC for confi guration of
network parameters.
4. Insert one end of the AC power adapter cable into the Power
port and the other end of the cable into a power outlet.
5. Turn the Power switch to the on position (|). All LEDs will fl ash
for one second; during this time, the STATUS LED will fl ash red,
yellow, and green.
Battery replacement
The gateway internal real time clock battery is designed to last up to
nine years under normal operating conditions. Should the battery fail
before that time, contact your service provider for assistance. Do not
attempt to replace the battery on your own; doing so could damage
the gateway.
Open Source License Statement
Cisco Connected Life Gateways may contain, in part, certain free
and/or open source software ("Open Source") under separate
license terms. Examples of such licenses may include all versions
of the GNU General Public License (GPL), GNU Lesser General
Public License (LGPL), BSD license, MIT license, Mozilla Public
License, Eclipse Public License, Apache license, and others. To fi nd
specifi c information regarding the Open Source in your product,
including copies of the applicable license documentation and related
information, go to: (i) for North America
web/consumer/support/open_source.html, or (ii) for outside North
America
http://www.cisco.com/web/consumer/support/open_
source.htm#~international. Once at the site, search for the product
listing and click the related items identifi ed. If you have any questions
or problems accessing any of the links, contact:
opensource-requests@cisco.com.
Last Updated: July 2014
Phillips
Screws
http://www.cisco.com/
spvtg-external-
Part Number: 78-100422-01A0
Advertisement
