Hydro Models Only 31 30 Assemble screw in this location with head to the inside. Frame **2405 31 30 NOTE: Unless noted other- wise, use the standard hard- ware torque specification chart. See the Table of Contents...
Ref. No. 7 includes Ref. Nos. 2 & 3 22 23 Torque to 45-62 ft. lbs. Torque to 15-25 ft. lbs. See Steering & Front Wheel Group Grease Lube spindle thru fittings with grease (2 places) See Steering & Front Wheel Group Hydro Models Gear Models Front Axle...
Page 7
All Models Front Axle REF. PART QTY. 176440 921133 1611703 1611705 1611708 1611710 1611715 1663114 1664847 1665601 1668147 1671260 1705918 1709305 1709785 1917372 1919326 1921210 1921333 1921525 1924361 1924940 1930651 1960020 1960114 1960362 DESCRIPTION SUPPORT ASSY., Axle, Rear (See Ref. No. 12) AXLE SUB ASSY.
Torque to 50-55 ft. lbs. NOTE NO. 1 loosen jam nut (Ref. No. 14) and index drag link (Ref. No. 1) to correct angle; torque jam nut to 13 ft. lbs. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents.
Apply sealant to threads. Locknut to engine. Apply anti- seize lubricant to crankshaft. RH Front on Gear Models; LH Front RH Rear on Hydro Models. 2, 3 6, 25 RH Rear on Gear Models (Zinc pltd. for grounding); 11, 13 RH Front on Hydro Models.
Page 11
1960251 * See your local Briggs & Stratton dealer for service parts. NOTE: Use Simplicity engine oil as follows (check inside front cover for part number): • SAE 30W SG/CC for temperature operating range of 32 • 5W30 SF/CD for temperature operating range of below 32 QTY.
Page 12
Use washers as req'd to adjust shift lever to neutral slot. Lubricate every 25 hours. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. .25 ± .03 clearance between pulley hub & snap ring on trans. Slide each bracket (Ref.
See Rear Wheels & Tires for assy. parts & mounting hardware NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Hydro Transaxle - Group 1 **2566...
Between frame & head of stud (Ref. No. 2) Grease pedal shaft and insert damper (Ref. No. 8) into pedal groove before assembling pedal (Ref. No 5). Small end of spring Install in uper hole on clutch pedal assy. arm. A minimum of two full threads must extend thru nut after assembly...
Lubricate bushings (Ref. No. 4) with grease. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Brake & Clutch - Hydro Models 18 20 Transmission Brake Arm Hook in center slot - rear of steering sump Apply anti-seize lubricant to Ref.
NOTE: Apply grease to ignition switch terminals (Ref. No. 14) and wire harness plug before connecting. Zinc Pltd. To Starter Motor Tie wrap wires together using Ref. No. 6 Mounts to To Magneto. lower RH hood hinge away from pivot pinch point and muffler Slide boot over termi- nal after securing to...
Page 24
Apply grease to ignition switch terminals (Ref. No. 14) and wire har- ness plug before con- necting. Zinc Pltd. Starter Motor Tie wrap wires together using Ref. No. 5. Mounts to lower R.H. hood hinge To Magneto away from pivot pinch point and muffler.
Page 26
NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Torque to 20-30 in. lbs. Hood, Grille, Dash & Fuel Tank Torque to 20-30 in lbs. (4 places) **2424 Brace (Ref. No. 6) must be assembled parallel to this surface.
Gear Models Seat supports must pivot freely when assembled Seat & Deck Hydro Models NOTE: Unless noted other- wise, use the standard hard- ware torque specification chart. See the Table of Contents. **1307...
NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Grease front wheel assemblies. Front Wheels & Tires...
Page 31
FRONT WHEEL & TIRE ASSY., Metallic Gray, 15 x 6.00-6 (Incl. Ref.Nos. 1, 8 & 10) TIRE, Front Wheel, 15 x 6.00-6 BEARING FRONT WHEEL ASSY., Metallic Gray, (Incl. Ref. Nos. 2 & 9) HUB CAP, 6" (Simplicity models only)
NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Qty. 1 or 2 (As required left wheel only) Rear Wheels & Tires...
Page 34
17, 18, 20 17, 18, 19 Located underneath hood Decals - Simplicity Models Located on LH side of wrapper to the right of the release lever. Located on LH side of wrapper above transmission fan. NOTE: Unless noted other- wise, use the standard hard- ware torque specification chart.
Located underneath hood 8, 10, 17 9, 11,16 7, 18 Decals - AGCO Allis Models Located on LH side of wrapper to the right of the release lever. Located on LH side of wrapper above transmission fan. NOTE: Unless noted other- wise, use the standard hard- ware torque specification chart.
Page 38
15, 17 16, 18 Located underneath hood Decals - Massey Ferguson Models 7, 13 Located on LH side of wrapper to the right of the release lever. Located on LH side of wrapper above transmission fan. NOTE: Unless noted other- wise, use the standard hard- ware torque specification chart.
Torque to 15-19 ft. lbs. (2 places). Torque to 50-70 ft. lbs.(2 places) 36" Mower Deck - Deck, Arbor & Blades Torque to 50-70 ft. lbs. Torque to 50-70 ft. lbs. (2 places). Apply gasket former to this surface, unless foam gasket (Ref.
Page 42
Torque to 15-19 ft. lbs. (2 places). Torque to 50-70 ft. lbs.(2 places) 36" Mower Deck - Deck, Arbor & Blades Torque to 50-70 ft. lbs. Torque to 50-70 ft. lbs. (2 places). Apply gasket former to this surface, unless foam gasket (Ref.
Page 43
All Models 36" Mower Deck - Deck, Arbor & Blades REF. PART QTY. 1930584 1930585 1931211 1931277 1931317 1931333* 1931348 1933263 1960373 Not Shown 1686609* * Optional Ref. Nos. 1 - 42 are on the preceding page. DESCRIPTION CAPSCREW, Hex Hd., 7/16-14 x 2-3/4 CAPSCREW, Hex Hd., 7/16-14 x 3-1/2 NUT, Hex, Flange, Whizlock, 3/8-16 NUT, Hex, Flange, Whizlock, 5/16-18...
30 19 P.T.O. Rod (see 36" roller & misc. group) NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. 36" Mower Deck - Clutch & Roller Support Grease 49 21 Coat O.D. with anti-seize lubricant.
Page 46
30 19 P.T.O. Rod (see 36" roller & misc. group) NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Grease 49 21 Coat O.D. with anti-seize lubricant. 36" Clutch & Roller Support Group Minimum .03"...
Page 47
All Models 36" Mower Deck - Clutch & Roller Support REF. PART 1919326 1920564 1921971 1922755 1923087 1923220 1923362 1924856 1924940 1924940 1928804 1928957 1930645 1931277 1931333 1960074 8191022 Ref. Nos. 1 - 40 are on the preceding page. QTY. DESCRIPTION WASHER, Plain CARRIAGE BOLT, 5/16-18 x 1-1/4...
Page 48
Assemble rolllers with ribs to inside as shown. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. 36" Mower Deck - Roller & Misc. Group Attach chain to right side of mower lift arm.
MODEL and SERIAL NUMBERS HERE NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Gear Transaxle Service Parts - Peerless Model 930-039 40 46...
Page 52
MODEL and SERIAL NUMBERS HERE NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Gear Transaxle Service Parts - Peerless Model 930-039 40 46...
NOTE: Unless noted otherwise, use the standard hardware torque specification chart. See the Table of Contents. Hydro Transaxle Service Parts - Hydro Gear Model 318-0500 17 17...
Page 55
Mfg. Nos. 1692403, 1692407, 1692412, 1692495 Hydro Transaxle Service Parts - Hydro Gear Model 318-0500 REF. PART 1709907 1709908 1709909 1709910 1709911 1709912 1709913 1709914 1709915 1709917 1709918 1709919 1709920 1709921 1709922 1713322 1713323 1713324 1713617 QTY. DESCRIPTION ARM, Bypass SEAL PUCK, Dampener SETSCREW...
Hardware Identification & Torque Specifications Common Hardware Types Hex Head Capscrew Carriage Bolt Standard Hardware Sizing When a washer or nut is identified as 1/2”, this is the Nominal size , meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the Nominal size , or body diameter is 1/2 inch;...