Advertisement
Model
A
(mm)
SW75
943
SW100
1350
SW120
1350
4
(mm)
B
C
(mm)
(mm)
950
175
950
175
950
175
• Avoid locations exposed to direct sunlight or other sources of heat.
• Select a location from which noise emitted by the unit will not inconvenience
neighbors.
• Select a location permitting easy wiring and pipe access to the power source and
indoor unit.
• Avoid locations where combustible gases may leak, be produced, À ow, or accu-
mulate.
• Note that water may drain from the unit during operation.
• Select a level location that can bear the weight and vibration of the unit.
• Avoid locations where the unit can be covered by snow. In areas where heavy
snow fall is anticipated, special precautions such as raising the installation loca-
tion or installing a hood on the air intake must be taken to prevent the snow from
blocking the air intake or blowing directly against it. This can reduce the airÀ ow
and a malfunction may result.
• Avoid locations exposed to oil, steam, or sulfuric gas.
• Use the transportation handles of the outdoor unit to transport the unit. If the unit
is carried from the bottom, hands or ¿ ngers may be pinched.
When installing the outdoor unit on a rooftop or other location unprotected from the
wind, situate the air outlet of the unit so that it is not directly exposed to strong winds.
Strong wind entering the air outlet may impede the normal airÀ ow and a malfunction
may result.
The following shows three examples of precautions against strong winds.
1 Face the air outlet towards the nearest available wall about 50 cm away from the
wall. (Fig. 2-3)
2 Install an optional air guide if the unit is installed in a location where strong winds
from a typhoon, etc. may directly enter the air outlet. (Fig. 2-4)
A Air outlet guide
3 Position the unit so that the air outlet blows perpendicularly to the seasonal wind
direction, if possible. (Fig. 2-5)
B Wind direction
Minimum dimensions are as follows, except for Max., meaning Maximum dimen-
sions, indicated.
The ¿ gures in parentheses are for SW100, 120 models.
Refer to the ¿ gures for each case.
1 Obstacles at rear only (Fig. 2-6)
2 Obstacles at rear and above only (Fig. 2-7)
•
Do not install the optional air outlet guides for upward airÀ ow.
3 Obstacles at rear and sides only (Fig. 2-8)
* 350 for SW50.
4 Obstacles at front only (Fig. 2-9)
* When using an optional air outlet guide, the clearance for SW100, 120 models is 500 mm or
more.
5 Obstacles at front and rear only (Fig. 2-10)
* When using an optional air outlet guide, the clearance for SW100, 120 models is 500 mm or
more.
6 Obstacles at rear, sides, and above only (Fig. 2-11)
* 350 for SW50.
•
Do not install the optional air outlet guides for upward airÀ ow.
Leave 350 mm for SW50 and 10 mm for SW75-120 space or more between the
units.
The ¿ gures in parentheses are for SW100, 120 models.
Refer to the ¿ gures for each case.
1 Obstacles at rear only (Fig. 2-12)
2 Obstacles at rear and above only (Fig. 2-13)
•
No more than 3 units must be installed side by side. In addition, leave space as shown.
•
Do not install the optional air outlet guides for upward airÀ ow.
3 Obstacles at front only (Fig. 2-14)
* When using an optional air outlet guide, the clearance for SW100, 120 models is 1000 mm
or more.
4 Obstacles at front and rear only (Fig. 2-15)
* When using an optional air outlet guide, the clearance for SW100, 120 models is 1000 mm
or more.
5 Single parallel unit arrangement (Fig. 2-16)
* When using an optional air outlet guide installed for upward airÀ ow, the clearance is 500
(1000) mm or more.
6 Multiple parallel unit arrangement (Fig. 2-17)
* When using an optional air outlet guide installed for upward airÀ ow, the clearance is 1000
(1500) mm or more.
7 Stacked unit arrangement (Fig. 2-18)
•
The units can be stacked up to two units high.
•
No more than 2 stacked units must be installed side by side. In addition, leave space as
shown.
Advertisement
