Summary of Contents for Danby Silhouette DKC646BLS
Page 1
GUIDE D’UTILISATION MANUAL DEL PROPIETARIO Model Modèle Modelo • • DKC646BLS CAUTION: Read and follow all safety rules and operating instructions before first use of this product. PRÉCAUTION : Veuillez lire attentivement les consignes de sécurité et les instructions d'utilisation avant l'utilisation initiale de ce produit.
Page 2
Tel: 1-800-26- Write down the model and serial numbers here. They are on a label located on the back of the cabinet. Model number DKC646BLS Serial number Date purchased Read this manual It contains instructions to help you use and maintain your keg cooler properly.
TABLE OF CONTENTS Important Safety Information Grounding Instructions Warning C0 Can be Dangerous! Safety Precautions Don’t Wait Do This Now! Important Notice Features Knowing your Keg Cooler Accessories Capacity Setting Up Your Keg Cooler Before putting your appliance into use Disposal of Packaging Location Outdoor Instructions...
IMPORTANT SAFETY INFORMATION READ ALL SAFETY INFORMATION BEFORE USING GROUNDING INSTRUCTIONS FOR YOUR SAFETY... Pertaining to the risk of Fire, Electric Shock or Injury to Persons. WARNING CO CAN BE DANGEROUS! Cylinders when charged contain high pressure compressed gas which can be hazardous if not handled properly.
IMPORTANT SAFETY INFORMATION SAFETY PRECAUTIONS • This appliance must be connected to a properly grounded electrical outlet ( see Grounding Instructions on pg. 4 ) • Do not operate this appliance if it has a damaged power cord or plug. •...
INCLUDED ACCESSORIES Remove and inspect all accessories supplied with this unit are present and in good condition. In the event any of the accessories are missing and /or not in good condition, please call Danby TOLL FREE at the number listed below and speak with one of our Customer Service Representatives.
KEG SIZES CYLINDER FEATURES There are three (3) standard size beer kegs that can be used in your Keg Cooler; 1/2 Barrel: 58.5 Liter Keg (15.5 Gal) Yields: 7 cases (1984ozs) of beer Keg Weight: 170lbs Full (approx.) 1/4 Barrel: 30 Liter Keg (7.75 Gal) Yields: 3-1/2 cases (992ozs) of beer...
SETTING UP YOUR KEG COOLER IMPORTANT: • Ensure that all included accessories are present and in good condition ( see ‘Included Accessories on pg. 7 ). • Make sure you have read and understood all important safety information on pages 4- DISPOSAL OF PACKAGING WE CARE ABOUT THE...
SETTING UP YOUR KEG COOLER ASSEMBLY INSTRUCTIONS 1. Installation of the Top Rail: See Fig. 1. 2. Installation of CO2 Regulator: Attach the CO2 Regulator to the CO2 cylinder by screwing the regulator nut onto cylinder valve and tighten (snug) using an adjustable wrench. See Fig.
Page 11
SETTING UP YOUR KEG COOLER ASSEMBLY INSTRUCTIONS (CONT’D) 5. Installation of C0 Air Line Hose to Regulator: Attach one end of the (red) air line hose to the hose barb connection on the CO 2 regulator. Secure hose by using one of the two (self locking) black plastic snap on clamps provided.
Page 12
SETTING UP YOUR KEG COOLER ASSEMBLY INSTRUCTIONS (CONT’D) 13. Making the connection between the Keg Coupler and Beer Keg: Before making (opening) connection between the keg coupler and beer keg, make sure the beer tower faucet is in the closed position.
SETTING UP YOUR KEG COOLER Changing Direction of the Door “Swing” TOOLS REQUIRED: Phillips #2 screwdriver WARNING! Excessive Weight Hazard Use two or more people to move and install the keg cooler. I M P O R TA N T ! Allow the unit to stand upright for 1 hour before putting the unit into operation.
OPERATING INSTRUCTIONS Electronic Controls TEMPERATURE INCREASE TEMPERATURE DECREASE LED DISPLAY FAHRENHEIT MODE CELSIUS MODE FAHRENHEIT/CELSIUS SELECTOR The electronic control panel allows for total cabinet temperature control as well as the option of displaying (current) and modifying (setting) the cabinet temperature in either Fahrenheit or Celsius. When you first plug in your Keg Cooler the LED will display the ‘live’...
OPERATING INSTRUCTIONS Replace an Empty Cylinder 1. Close the main cylinder valve (A) by turning in a clockwise direction. See Fig.12 2. Close the secondary shut-off valve (C) by turning to "horizontal" (east/west) position on lower stem pipe. See Fig.12 3.
OPERATING INSTRUCTIONS Using Proper Draw Technique Using the proper draw technique to dispense beer should allow you to fill an 8 oz glass leaving approxi mately 3/4”- 1” of ‘foam’. Fig. 13 DO NOT... • Begin the draw with the glass in an upright position.
CLEANING AND MAINTENANCE... Regular cleaning and maintenance is a key factor in safe guarding the longevity of the keg, the quality of the dispensed beer as well as trouble free day to day operation your Keg Cooler..of the Keg Cooler ...
CLEANING AND MAINTENANCE..of the “Beer Clean” Glassware ... of the CO Pressure ... of the Beer Keg Draught Beer should be treat- ed as a food product. It is very important that you store and handle it properly. •...
BEFORE YOU CALL FOR SERVICE TROUBLESHOOTING Problem Possible Causes Excess formation of Recent keg agitation foam ‘head’. Improper regulator setting Internal temperature of keg cooler (or beer keg) too warm. Pressure build up Improper draw technique Flat Draft, no Improper regulator formation of foam.
Page 20
BEFORE YOU CALL FOR SERVICE TROUBLESHOOTING (Cont’d) Problem Possible Causes Dispense system Sputtering draw requires cleaning. Keg Coupler installed incorrectly Line or dispenser obstructions. Improper draw technique Handle not fully returned Faucet Dripping to close position. Faucet requires cleaning. Rapid C0 cylinder Improper connection, air line leak.
LIMITED PRODUCT WARRANTY This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer. This warranty is available only to the person to whom the unit was originally sold by Danby or by an authorized distributor of Danby, and is non-transferable. Plastic parts (ie.
Page 22
Model Modèle Modelo • • DCK646BLS For service, contact your nearest service depot or call: 1-800-26- Danby (1-800-263-2629) to recommend a depot in your area. En cas de réparation, veuillez contacter votre service après-vente le plus près ou communiquez au: 1-800-26- Danby (1-800-263-2629)