Table of Contents
Related Manuals for Sherwood TX-5090C
Summary of Contents for Sherwood TX-5090C
- Page 1 OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG ISTRUZIONI PER L’USO MANUAL DE INSTRUCCIONES TX-5090C/RDS AM/FM Stereo Digital Tuner Digital-Tuner für UKW Stereo, MW und LW Sintonizzatore Stereo Digital AM/FM Sintonizador AM/FM Estéreo Digital...
-
Page 2: Introduction
Introduction Introduction UNPACKING AND INSTALLATION UNPACKING AND INSTALLATION Congratulations on your purchase! Your new high fidelity Tuner is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. -
Page 3: Read This Before Operating Your Unit
Introduction READ THIS BEFORE OPERATING YOUR UNIT FOR U.S.A. AND CANADA FOR YOUR SAFETY Units shipped to the U.S.A. and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. -
Page 4: Table Of Contents
Introduction CONTENTS Introduction UNPACKING AND INSTALLATION READ THIS BEFORE OPERATING YOUR UNIT Rear Panel Connections Front Panel Controls Operations LISTENING TO RADIO BROADCASTS LISTENING TO FM STEREO BROADCASTS PRESETTING RADIO STATIONS LISTENING TO PRESET STATIONS LISTENING TO RDS BROADCASTS (FM only) (Additional Function for TX-5090RDS Only) Troubleshooting Guide Specifications... -
Page 5: Rear Panel Connections
Rear Panel Connections Do not plug the AC input cord into the AC outlet when making connections. Be sure to connect the white plugs to the L(Left) and the red plugs to the R(Right) jacks when making connections . Refet to the connecting diagram in the operating instractions of AMPLIFIER/RECEIVER. (OUTDOOR ANTENNA) ④... - Page 6 An FM outdoor antenna can be connected to the tuner with a 75 coaxial cable. ⑤ DIGI LINK JACKS Connect this jack to the DIGI LINK jack of Sherwood amplifier such as AX-5090R,etc. bearing the DIGI LINK III or II logo to control this unit remotely by DIGI LINK system.
-
Page 7: Front Panel Controls
Front Panel Controls ① ① POWER SWITCH Press this switch to turn the power on and press again to turn the power off. For system operation, plug the AC input cord into the switched AC outlet on amplifier, keep the POWER switch ON and control power ON/OFF with the power operation on the amplifier. -
Page 8: Fluorescent Display
This unit can be remotely controled with Sherwood DIGI LINK III amplifier such as AX-5090R. For available functions, refer to the compatiable unit's operating instructions. To listen to a TUNER by DIGI LINK system, first make DIGI LINK connection between this unit and Sherwood compatiable amplifier such as AX-5090R. -
Page 9: Operations
Operations LISTENING TO RADIO BROADCASTS Auto tuning Turn the power on. Each time the POWER switch is pressed, this unit is turned on or off. Press the TUNING UP(▲) or DOWN(▼) button for more than 0.5 second. This unit will now search until a station of sufficient strength has been found. -
Page 10: Presetting Radio Stations
PRESETTING RADIO STATIONS You can store up to 30 preferred stations in the memory. Tune in the desired station with auto or manual tuning. Example)When memorizing FM broadcast of 91.9MHz in preset memory. ST TUNED Select the desired preset number. ST TUNED When using the PRESET NUMERIC buttons on the front panel,... -
Page 11: Listening To Preset Stations
LISTENING TO PRESET STATIONS When using the PRESET NUMERIC buttons Press the preset number of the desired station. Example) When selecting “9” When using the PRESET SCAN button Press this button to start scanning. ST TUNED The unit starts scanning the preset stations in the preset sequence and each station is received for 5 seconds. -
Page 12: Listening To Rds Broadcasts(Fm Only)
Additional Function for TX-5090RDS Only LISTENING TO RDS BROADCASTS(FM only) RDS(Radio Data System) is a method for sending information signals together with the transmitter signals.. Your tuner is capable of translating these signals and putting the information on the display. These codes contain the following informations. - Page 13 PTY search Use this function to automatically search and receive the stations broadcasting the desired program type. In the FM mode, select the PTY search mode. "PTY SRCH" is displayed. Start searching. The tuner automatically searches a station offering PTY services.
- Page 14 EON TA Use this function to automatically search and receive the traffic announcement while listening to traffic program. In the TP mode. Traffic program is displayed and the TA indicator lights up. If the preset station broadcasting traffic announcement is found, it will be tuned in while listening to traffic program.
-
Page 15: Troubleshooting Guide
Troubleshooting Guide If your unit should not perform as expected, consult the table below to see if the problem can be corrcted before seeking help from your dealer or our service organization. PROBLEM No power The AC input cord is disconnected. The POWER switch is not pressed completely. -
Page 16: Specifications
Specifications FM TUNER SECTION Tuning frequency range...87.5~108 MHz Usable sensitivity, THD 3%, S/N 26 dB ...15.2 dBf 46 dB quieting sensitivity, mono/stereo ...23.2/43.2 dBf Signal to noise ratio, 65 dBf, mono/stereo...70/65 dB Total harmonic distortion, 65 dBf,1 kHz, mono/stereo...0.4/0.6% Frequency response, 20 Hz~15 kHz ...±3 dB Stereo separation, 1 kHz ...35 dB Capture ratio...2 dB IF rejection ratio... - Page 17 5707-04715-002-0...