Table of Contents
Advertisement
Quick Links
ELECTRIC SMOKER OVEN
Model 90898
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright
2003 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
90898 manual.PMD
1
12/4/2003, 12:58 PM
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools 90898
Summary of Contents for Harbor Freight Tools 90898
- Page 1 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. 90898 manual.PMD...
-
Page 2: Product Specifications
Keep bystanders, children, and visitors away while operating an Smoker Oven. The Smoker Oven generates dangerous heat. Provide barriers or shields as needed. SKU 90898 PAGE 2 90898 manual.PMD 12/4/2003, 12:58 PM... -
Page 3: Electrical Safety
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 90898 PAGE 3 90898 manual.PMD... - Page 4 When servicing a product, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SKU 90898 PAGE 4 90898 manual.PMD 12/4/2003, 12:58 PM...
-
Page 5: Specific Safety Rules
SPECIFIC SAFETY RULES Maintain labels and nameplates on the Smoker Oven These contain important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. -
Page 6: Grounded Tools: Tools With Three Prong Plugs
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 90898 PAGE 6 90898 manual.PMD 12/4/2003, 12:58 PM... -
Page 7: Extension Cords
If you are using one extension cord for more than one product, add the name plate amperes and use the sum to determine the required minimum cord size. (See Figure C.) SKU 90898 PAGE 7 90898 manual.PMD 12/4/2003, 12:58 PM... - Page 8 Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions xxxx/min. per Minute (RPM) SKU 90898 PAGE 8 90898 manual.PMD 12/4/2003, 12:58 PM...
- Page 9 When unpacking, check to make sure all the parts shown on the Parts List on page 12 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
- Page 10 1. The Thermostat (1) knob ranges from 90 to 250 degrees. Turn the knob clockwise to turn on the unit. It will take from 30 to 90 minutes to reach the desired heat (depending on the load size). SKU 90898 PAGE 10 90898 manual.PMD...
-
Page 11: Inspection, Maintenance, And Cleaning
10. Replace the Grills (5, 5a) and the Wood Box (60. SKU 90898 PAGE 11 90898 manual.PMD 12/4/2003, 12:58 PM... -
Page 12: Parts List And Assembly Diagram
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90898 PAGE 12 90898 manual.PMD 12/4/2003, 12:58 PM...