Advertisement
Quick Links
Panacea
®
6300 Bariatric Bed
Content and Assembly Manual
Read this Content and Assembly Manual, along with your Owner's Manual, completely and carefully before
proceeding with assembly procedures. Refer to your Owner's Manual for important definitions and symbols.
If you do not feel capable of performing this assembly, STOP – please contact Direct Supply
Equipment
®
& Furnishings
or a capable service person to finish the assembly for you. Improper assembly will affect
®
user safety and may void your warranty.
1-800-634-7328 DirectSupply.com
Advertisement
Related Manuals for Panacea 6300
Summary of Contents for Panacea 6300
- Page 1 Panacea ® 6300 Bariatric Bed Content and Assembly Manual Read this Content and Assembly Manual, along with your Owner’s Manual, completely and carefully before proceeding with assembly procedures. Refer to your Owner’s Manual for important definitions and symbols. If you do not feel capable of performing this assembly, STOP – please contact Direct Supply Equipment ®...
-
Page 2: Package Contents
Package Contents Panacea 6300 Package Contents: (1) main bed assembly (2) headboards and footboards (2) assist devices (1) wall guard (2) head and foot mattress rails (2) front mattress side guards (2) lower mattress side guards (1) handheld pendant (2) footboard mounts (2) headboard mounts with I.V. - Page 3 Assembly STEP 1. Uncrate the Bed Cut black strapping around box and remove box enclosing bed frame. Using a claw hammer or a pry bar, carefully remove the wooden planks from the top and sides of the crate by prying against the existing boards.
- Page 4 Assembly (cont.) STEP 2. Remove Cardboard Packaging Using a utility knife with a fresh blade for safety, carefully cut along the sides of the box after removing the box lid and casting it aside. Remove any and all cardboard and foam packaging surrounding the bed.
- Page 5 STEP 3. Unwrapping Main Bed Assembly Using your utility knife with a fresh blade for safety, carefully remove all plastic packaging around the bed and wooden shipping frame. All Styrofoam and cardboard parts used during shipping should be discarded at this time. Cut and remove all plastic ties. Any loose or wrapped parts sitting on top of the bed assembly should be cautiously unwrapped and set aside where they will not be damaged.
- Page 6 Assembly (cont.) STEP 4. Removing Wall Guard Using care, manually raise the headboard section of the bed to an upright fixed position. Cut nylon ties along the lift rails and free the wall guard. Remove all packaging and set wall guard aside.
- Page 7 STEP 5. Handrail Removal Once the wall guard has been removed, you will see a separate cardboard container underneath the main bed frame’s headboard section. This box contains the handrails and is bound securely to the wooden sub frame via thick nylon ties. Although a utility knife can be used to cut these ties, it is easier and safer to use a pair of side-cutters to remove the straps.
- Page 8 Assembly (cont.) STEP 6. Test Bed Functions Once the bed is free from all packaging constraints, unwrap and unravel the electrical cord attached to the bottom of the electric motor assembly found underneath the bed. Plug bed into a standard 3-prong 110V wall outlet. Using the hand pendant controller, put the bed through all of its proper function cycles of raised and lowered heights and contour functions.
- Page 9 STEP 7. Handrail Placement Mount to mattress rail on headboard side only Mount only between first rung of forward mattress rail WARNING: Please take careful note to ensure the correct placement of the handrail. If the rail is placed incorrectly, it may pose an entrapment risk to your resident. Resident entrapment with rails may cause injury or death.
-
Page 10: Step 8. Footboard Assembly
Assembly (cont.) Step 8. Footboard Assembly Note placement of inner stops when assembling footboard Locate a headboard/footboard, (4) large hex head barrel shaft bolts, (4) plastic headboard/ footboard spacers and your (2) footboard mounts. Please note the correct location of the stopper on inside of the footboard mounts. -
Page 11: Step 9. Headboard Assembly
STEP 9. Headboard Assembly Note placement of inner stops when assembling footboard Locate a headboard/footboard, (4) large hex head barrel shaft bolts, (4) plastic headboard/footboard spacers and your (2) headboard mounts. Please note correct location of the stopper on the inside of the headboard mounts. - Page 12 Assembly (cont.) STEP 10. Headboard and Footboard Placement Locate the two head and foot mount rails with locking knobs. Slide each rail into the end of the frame with the mount receptacle facing upward. Adjust proper desired length and fasten to frame using (4) small button head hex bolts.
- Page 13 STEP 11. Completed Bed Removal from Wooden Sub Frame This step requires four able individuals to remove the assembled bed from the wooden sub frame. Each individual will be required to lift 100 lbs. off of the frame and walk it aside. Although the bed does not need to be lifted more than a few inches to clear the wood frame, this task can be strenuous for a smaller individual or someone with known back issues.
- Page 14 Assembly (cont.) STEP 12. Wall Guard Placement Locate the wall guard removed earlier from underneath the bed. The wall guard should be inserted into the round, drilled receptacles found under the headboard section of the bed. The guard features sprung ball socket locks along the inner rails. They will need to be depressed as you clear each hole in the receptacle.
- Page 15 YOU HAVE NOW COMPLETED THE ASSEMBLY OF YOUR PANACEA 6300 BARIATRIC BED. ® Be sure to double-check all bolts and part placements on the bed. Also, be sure to remove all packaging materials from the area before allowing residents into the area. Place the bed against the wall and supply electricity.
- Page 16 Direct Supply , Inc. Distributed by Direct Supply Manufacturing, Inc. 6699 N Industrial Road, Milwaukee WI 53223. ® © 2011-2015 Direct Supply Manufacturing, Inc. All Rights Reserved. Direct Supply , Panacea , and all associated logos are the ® ®...