PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
Page 12
IC DESCRIPTION IC, CXA2523AR Pin No. Pin Name Description Input “I” RF signal converted to I-V. Input “J” RF signal converted to I-V. Output voltage for VCC/2. Input current for main beam servo signal A. Input current for main beam servo signal B. Input currentt for main beam servo signal C.
Page 13
Pin No. Pin Name Description COMPP User comparator non-inverted input pin. ADDC Capacitor connection pin for ADIP amplifier on return circuit. Not used. Non-inverted input pin for user operational amplifier. RF amplifier output pin. Check point for eye pattern. MORFI Input pin where Groove RF signal is AC coupled.
Page 14
IC, CXD2654R Pin No. Pin Name Description MNT0 MNT1 Monitor output terminal. MNT2 MNT3 SWDT Microprocessor serial interface data input. SCLK Microprocessor serial interface shift clock input. XLAT Microprocessor serial interface latch input. Latched at falling down edge. SRDT Microprocessor serial interface data output. The terminal which outputs internal status in accordance with the address of the SENS microprocessor serial interface.
Page 15
Pin No. Pin Name Description Eternal DRAM address output. Eternal DRAM address output. (Not connected) DVSS — Digital ground. External DRAM output enable. ________ XCAS External DRAM CAS output. External DRAM address output. ________ XRAS External DRAM RAS output. External DRAM write enable. External DRAM data bus.
Page 16
Pin No. Pin Name Description ADFG ADIP2 binary-converted FM signal (22.05±1 kHz) input. F0CNT Current source setting output terminal to CXA2523. XLRF Latch output for CXA2523 control. Latched at rise-up. CKRF Shift clock output for CXA2523 control. DTRF Data output for CXA2523 control. APCREF Reference PWM output to laser APC.
Page 17
IC, CXP81960M-561R Pin No. Pin Name Description MCAS — MRAS — Not used. — AMUTE Audio mute signal output. Serial clock output for EEPROM interface. Serial data output for EEPROM interface. Serial data input for EEPROM interface. EEPROM chip select signal output. —...
Page 18
Pin No. Pin Name Description ARDY READY input signal for system control interface. Serial data input for system control interface. SOUT Serial data output for system control interface. ACLK Serial clock output for system control interface. XLAT Latch signal output for CXD2654 interface. ________ CXD2654 reset signal output.
Page 19
Pin No. Pin Name Description — Not used. Connected to VSS. Open. — Connected to VSS. — Connected to VDD. — — Not used. DRVMUTE BA5970FP mute signal output. — — Not used. — — RECP Laser power select signal output. Record data output enable signal output.
MECHANICAL PARTS LIST 1/1 REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION 1 8Z-ZG2-220-010 LEVER,SW RACK A 21 8Z-ZG2-238-010 HLDR,MECHA STOP 2 8Z-ZG2-221-010 LEVER,SW RACK B 22 8Z-ZG2-241-010 HLDR,ASSY M SUB L 3 8Z-ZG1-606-010 FF-CABLE, 8P 1.0 115MM 23 8Z-ZG2-243-010 HLDR,ASSY M SUB R 4 8Z-ZG2-613-010...
Page 22
MECHANISM EXPLODED VIEW 1/1 (ZZG-1 A) MOT, M25E-4 CHAS MAIN SUB LOAD C.B 7ZG-3 A1...
Page 23
MD MECHANISM PARTS LIST 1/1 (ZZG-1 A) REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION 1 87-ZG8-257-210 LEVER ASSY,REC 16 87-ZG8-231-010 LEVER,SHUTTER 2 8Z-ZG1-220-010 LEVER,SW EJECT 17 87-B10-130-010 W-P,1.23-3.1-0.25 SLIT 3 8Z-ZG1-201-010 CHAS ASSY,MAIN 18 8Z-ZG1-221-010 LEVER,SW PLAY 4 8Z-ZG1-248-010 PLATE,CTRG...