Dremel DIGILAB LC40 Operating And Safety Instructions Manual
  1. Manuals
  2. Brands
  3. Dremel Manuals
  4. Cutter
  5. DIGILAB LC40
  6. Operating and safety instructions manual

Dremel DIGILAB LC40 Operating And Safety Instructions Manual

Laser cutter
Hide thumbs Also See for DIGILAB LC40:
Table of Contents

Advertisement

Quick Links

IMPORTANT READ BEFORE USING
Operating / Safety Instructions
Dremel DIGILAB
LC40 Laser Cutter
P.O. Box 081126 Racine, WI 53408-1126
Call Toll Free for Consumer Information & Service Locations
1-844-4DRML3D (1-844-437-6533) www.dremel.com
ENGLISH VERSION

Advertisement

Table of Contents
loading

Related Manuals for Dremel DIGILAB LC40

Summary of Contents for Dremel DIGILAB LC40

  • Page 1 IMPORTANT READ BEFORE USING Operating / Safety Instructions Dremel DIGILAB LC40 Laser Cutter P.O. Box 081126 Racine, WI 53408-1126 Call Toll Free for Consumer Information & Service Locations 1-844-4DRML3D (1-844-437-6533) www.dremel.com ENGLISH VERSION...

  • Page 2: Table Of Contents

    Attach Exhaust Shroud ... .23 Firmware and Open Source Software . . .87 Exhaust Connection ... .24-29 Dremel Limited Warranty ... .88...

  • Page 3: General Safety Warnings

    GENERAL SAFETY WARNINGS Read all safety warnings, instructions, illustrations and specifications provided with this laser cutter. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. READ ALL INSTRUCTIONS SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE Work Area Safety use any adapter plugs with earthed (grounded) laser cutters.

  • Page 4: Laser Cutter Safety Warnings

    GENERAL SAFETY WARNINGS clothes, jewellery or long hair can be caught Maintain laser cutters. Check for in moving parts. misalignment or binding of moving parts, breakage of parts and any other condition Be careful removing work pieces from the that may affect the laser cutter’s laser cutter.

  • Page 5: Additional Safety Warnings

    LASER CUTTER SAFETY WARNINGS the chassis and increase the risk of eye Discontinue use and seek fresh air if injury. respiratory or eye irritation occurs. Ensure ventilation, exhaust, and/or Do not operate the laser machine with filtration systems are working according any of the panels removed.

  • Page 6: Symbols

    FOR FUTURE REFERENCE. SYMBOLS IMPORTANT: Some of the following symbols may be used on the Laser Dremel LC40 Cutter. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol...

  • Page 7: Fcc Compliance

    The Dremel LC40 may not be used to create objects using digital files or digital designs If you use the Dremel LC40 in any way other protected by intellectual property rights than as recommended and described in owned by third parties without such third these Operating/Safety Instructions, you do parties’...

  • Page 8: Specifications

    Working Current: 20mA •Microsoft® Windows® 8.1 Wavelength: 10.6 μm •Microsoft® Windows® 7 SP1 Browser Compatibility: Chrome, Safari, DREMEL LC40 LASER CUTTER Firefox, & Internet Explorer WEIGHT & DIMENSIONS Min Screen Resolution: 1024 x 768 Pixels Dimensions: 32” x 20” x 8.25”...
  • Page 9 SPECIFICATIONS DREMEL LC40 LASER CUTTER & HEX BOX™ CLEARANCE REQUIREMENTS WALL 8” 8” (203mm) (203mm) Min. Min. Laser Cutter 30” (762mm) 8” 8” (203mm) (203mm) Min. Min. Laser Cutter Hex Box™ X – must be at least 26" (660 mm) when using onboard fan and at least 10" (254 mm) when using external booster fan.

  • Page 10: Material Usage

    • Pressure treated • Stained Nylon While the Dremel LC40 Laser Cutter can cut and etch a variety of materials, some materials such as most metals, cannot be marked and will give less than desirable results. Other materials may not have acceptable finish quality.

  • Page 11: Resources

    Location Quick Start Provides an illustrated walkthrough of Printed version is located in Guide how to un-box the Dremel LC40 Laser the box with the Dremel Cutter and start a job. LC40 Laser Cutter. It is also available on digilab.dremel.com/support/...
  • Page 12 GLOSSARY OF TERMS Duct that is connected to the Dremel LC40 Laser Cutter unit to vent exhaust Exhaust Hose outside or into a filtration unit or to outside ventilation. A metal tubing connection that is screwed onto the rear of the Dremel LC40 Exhaust Shroud Laser Cutter unit over the exhaust vent fan.

  • Page 13: Introduction

    Laser Head. Workspace b) A screen in the Dremel LC40 Control Software where a job is created. It provides a graphical representation of the intended job and its position relative to the general boundaries of the laser working area.

  • Page 14: Unpacking

    Honeycomb Plate. 2. Remove Instructional Manual, Water 4. Open the Lid of the Dremel LC40 Hoses, Air Tube, Screws, Hex Box™ Laser Cutter to reveal box 3 with Hex Cap, Hex Keys, Spacer Puck from box 2.

  • Page 15: Kit Contents

    KIT CONTENTS The Dremel LC40 Laser Cutter is shipped with the following included parts and accessories: Reusable Tote Bag Project Sample Honeycomb Plate Quick Start Guide Material IMPORTANT IMPORTANT IMPORTANTE Read Before Using Lire avant usage Leer antes de usar Operating / Safety Instructions Consignes d’utilisation/de sécurité...

  • Page 16: Getting To Know Your Dremel Lc40 Laser Cutter

    GETTING TO KNOW YOUR DREMEL LC40 LASER CUTTER ig. 1 Dremel LC40 Laser Cutter 14. Power Switch 15. Power Cord 1. Lid 16. Hex Box™ Power Outlet 2. LCD Touchscreen 17. Air Inlet 3. Start Button 18. Exhaust Shroud 4. USB Port (for service only) 19.
  • Page 17 GETTING TO KNOW YOUR DREMEL LC40 LASER CUTTER ig. 2 2 . 0 ”...
  • Page 18 GETTING TO KNOW YOUR LASER CUTTER REAR VIEW OF DREMEL LC40 LASER CUTTER ig. 3 WAT ER OUT SORT IE D’EA U SALI DA DE AGUA WAT ER IN ENTR ÉE D’EA U ENTR ADA DE AGUA REAR VIEW OF HEX BOX™...

  • Page 19: Setup

    SETUP Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Disconnect the plug from the power source before making any assembly, adjustments or changing accessories.

  • Page 20: Install Honeycomb Plate

    Install Honeycomb Plate Place the Honeycomb Plate inside the laser on the laser bed. Be careful not to damage any part of the Dremel LC40 Laser Cutter during this process. The head can be moved out of the way by hand if necessary.

  • Page 21: Attach Water Hoses

    Water Hose Clear Blue Hose Water Water Hose Hose Fig. 8 — Rear of Dremel LC40 Laser Cutter Fig. 9 — Rear of Hex Box™ Push the ends of the tubing onto the fittings until they are snug. Correct Incorrect...

  • Page 22: Attach Air Tube

    Air Tube Fitting Hex Box Air Tube Air Tube Fig. 11 — Rear of Hex Box™ Fig. 10 — Rear of Dremel LC40 Laser Cutter Push the ends of the tubing onto the fittings until they are snug. Correct Incorrect...

  • Page 23: Attach Hex Box™ Cord

    Connector Connector Cord Cord Fig. 12 — Rear of Dremel LC40 Laser Cutter Fig. 13 — Rear of Hex Box™ Using a screwdriver, attach the Exhaust Shroud to the back of the Dremel LC40 Laser Cutter, Fig. 14. Ensure that the...

  • Page 24: Exhaust Connection

    10 minutes after the job is finished to including those for hazardous or noxious evacuate exhaust out of the Dremel LC40 exhaust ventilation systems. Consult with Laser Cutter. Wait at least 30 seconds federal, state and/or local authorities and...
  • Page 25 N/A = Exhaust management method not applicable for this use location. * Room size is based on ceiling height of 8.5 feet. Adjust room size for actual ceiling height. Do not use Dremel LC40 Laser Cutter in rooms smaller than specified in Table 3.
  • Page 26 Table 3. Always operate the Dremel exhaust ventilation systems. LC40 Laser Cutter in a well-ventilated area. • Ducts must be installed so they are not Do not operate the Dremel LC40 Laser damaged or ruptured.
  • Page 27 10 feet of exhaust duct is improve exhaust flow through the duct. needed between the Dremel LC40 Laser Clamp 4 ft Max. Clamp Fig. 16: Exhaust management system example using the Dremel LC40 Laser Cutter onboard fan.
  • Page 28 • If using flexible duct, you may use the sure to choose correct ventilation option provided Hose Clamps to secure duct to on the Touch Screen during the Dremel Laser Cutter Exhaust Shroud and LC40 Laser Cutter startup sequence. The External Booster Fan inlet.
  • Page 29 When selecting a filtration unit be sure it is exhaust ventilation systems. The design suitable for use with laser cutters/ flow rate of exhaust from the Dremel LC40 engravers. The filtration unit should be Laser Cutter must be a minimum of 90 Underwriters Laboratory listed.

  • Page 30: Plug In Dremel Lc40 Laser Cutter

    SETUP Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Plug in the Dremel LC40 Laser Cutter...

  • Page 31: Turn On The Dremel Lc40 Laser Cutter

    Turn On the Dremel LC40 Laser Cutter Locate the Power Switch at the back of ig. 20 the unit (above the Power Cord) and turn the Dremel LC40 Laser Cutter on, Fig. 20. Power Switch Get Started When the unit is powered on for the first...

  • Page 32: Fill Hex Box™ With Distilled Water

    SETUP Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Fill Hex Box™ with Distilled Water Do not spill water on 3.

  • Page 33: Connect A Computer To The Dremel Lc40 Laser Cutter

    SETUP Connect a Computer to the Dremel LC40 Laser Cutter For a hardwire connection: 1. Connect the Ethernet Cord to the Dremel LC40 Laser Cutter (Fig. 22) ig. 22 and the computer. 2. Open an internet browser window on the computer.

  • Page 34: Network Setups

    • The Dremel LC40 Laser Cutter does not have access to the Internet (optional for Dremel LC40 Laser Cutter connection) unless the computer bridges/shares the Internet connection. Note: The Dremel LC40 Laser Cutter does have the option to set a Static IP address using the LCD software interface. Ethernet Wireless or Ethernet ig.
  • Page 35 Ethernet Connection. In this scenario, the user does have an Internet connection through the router. • One or more computers access the Dremel LC40 Laser Cutter as well as the Internet through the Router.

  • Page 36: Lcd Touch Screen

    LCD TOUCH SCREEN Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.
  • Page 37 Status Bar Status Icon Name What it means Dremel LC40 Laser Cutter is connected to a computer or a Ethernet network router via Ethernet Port. The icon will disappear when there is no Ethernet connection. Dremel LC40 Laser Cutter is connected to a computer or network router via wireless.
  • Page 38 LCD TOUCH SCREEN HOME > UNLOCKED LASER HOME – Moves the Laser Head back to its origin location. Button will flash when homing is necessary. HOME JOB HISTORY TOOLS NETWORK JOG SPEED – Toggles between fast and slow Laser Head movement speed. Fast is default speed.
  • Page 39 FAST 192.168.1.115 v1.0.0 JOB HISTORY This tab displays jobs received by the Dremel LC40 Laser Cutter. As received from the factory, this list is empty. The Factory Reset option will clear Job History. Job creation is explained in the Software Section.
  • Page 40 LCD TOUCH SCREEN JOB HISTORY This screen displays options for the Job selected from the list. DELETE – Delete files from the Job History list. RUN PERIMETER – Executes the run perimeter. NEXT – Changes the text to LOADING. The Job will prepare to start.
  • Page 41 LCD TOUCH SCREEN TOOLS > MENU SCREEN This screen displays available tools for management of the Dremel LC40 Laser Cutter. ABOUT — Displays Dremel LC40 Laser Cutter information such as model number, serial number, firmware version, usage, and network information.
  • Page 42 LCD TOUCH SCREEN TOOLS > ABOUT THIS DEVICE This screen displays Dremel LC40 Laser Cutter hardware and software information. MODEL NUMBER — Displays unit model number. SERIAL NUMBER — Displays unit serial number. FIRMWARE NUMBER — Displays the currently installed firmware version.
  • Page 43 LCD TOUCH SCREEN TOOLS > SETTINGS This screen displays available settings LANGUAGE – Displays a sub-menu where LCD menu warnings language can be selected. LIGHTS – Displays a sub-menu where cabinet LED lights can be turned “ON” and “OFF”. VENTILATION – Displays a sub-menu screen where ventilation type can be selected.
  • Page 44 To assure proper removal of fumes produced during operation of Dremel LC40 Laser Cutter, the ventilation selection must match the actual fume extraction set up. Dremel LC40 must be set up according to instructions provided in the Exhaust Management chapter of the Setup section beginning on page 24 to assure proper ventilation.
  • Page 45 LCD TOUCH SCREEN TOOLS > SETTINGS > PRIME WATER PUMP This screen provides control to start the water pump during priming of the laser cooling system. START – Starts the coolant pump. This screen provides control to stop the water pump during priming of the laser cooling system.
  • Page 46 FOCUS LASER HEAD – Instructions for adjusting the Laser Head to focus the laser beam on the work piece surface. MACHINE SETUP – Instructions for the initial setup of Dremel LC40. OTHER – Instructions for cleaning of the mirrors and lens.
  • Page 47 LCD TOUCH SCREEN TOOLS > TUTORIALS Sequence of screens stepping through JOB PREP. Sequence of screens stepping through HOOK UP.
  • Page 48 This screen displays available test files and allows their execution. Test files are used to verify proper operation of select functions and features of Dremel LC40 Laser Cutter. • Test Files "CUT TEST - BOX 1" thru "CUT TEST - BOX 12"...
  • Page 49 LCD TOUCH SCREEN TOOLS > UPDATE SERVICE This screen provides network connectivity and status of update service from Dremel. LOCAL NETWORK – Shows whether ethernet or wireless is connected to the local network. UPDATE SERVICE – Indicates if the unit is able to communicate with the update service (Internet connection is required).
  • Page 50 WIRELESS – Setup or modify a wireless local area network connection for the Dremel LC40 Laser Cutter to connect to. STATIC IP – Setup the Dremel LC40 Laser Cutter to use a Static IP address or default 000.000.000 to a DHCP (Dynamic Host Configuration...
  • Page 51 TOUCH SCREEN NETWORK > WIRELESS This screen displays wireless networks detected by the Dremel LC40 Laser Cutter. Selecting an available network will start the connection process. Wireless network signal strength indicator. This screen displays the password prompt that appears when a password protected wireless...
  • Page 52 TOUCH SCREEN NETWORK > WIRELESS This screen displays a notification that appears when a successful wireless network connection is made. DONE – Return to Network menu screen. This screen displays a notification that appears when connection to the wireless network is unsuccessful.
  • Page 53 Configuration Protocol address IP address. Values displayed on IP Address, Netmask, and Gateway are ignored but saved for future use. AUTO DNS – Allows the Dremel LC40 Laser Cutter to use the domain name system server as determined by the network router.
  • Page 54 OPERATION SCREENS These screens appear during operation. CHECKLIST SCREEN This screen displays system checks performed automatically by the Dremel LC40 Laser Cutter and operator inputs that must be completed before a job can be started. CHECKLIST SCREEN — ERRORS DETECTED Displays errors detected in systems of the Dremel LC40 Laser Cutter while it is preparing to start a job.
  • Page 55 TOUCH SCREEN OPERATION SCREENS If all icons at the top are white, then items in the checklist should be green. Manual checks that can be completed after the work piece is placed in the workspace and Laser Head adjusted using the spacer puck.

  • Page 56: Laser Control Software

    LC40 Control Software. The LC40 Control Software will link a web browser with the Dremel LC40 Laser Cutter using the IP address (found at the bottom of the LCD home screen) on the local connection (Wireless or Ethernet).
  • Page 57 SELECT ALL — select to select all. DESELECT ALL — select to deselect all. C. HELP ABOUT YOUR LASER — select to see more details about your Dremel LC40 Laser Cutter. MANUAL — select to access the Dremel LC40 Laser Cutter Operating/Safety Instructions.
  • Page 58 DREMEL LC40 CONTROL SOFTWARE Tool Bar IMPORT UNDO REDO AUTO ARRAY MATERIAL TIME: 00:00:00 OPTIONS RUN PERIMETER START IMPORT UNDO Click to import a file or use the camera Click to undo most recent action/change. capture feature to create a file or place a...
  • Page 59 MATERIALS Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death Never engrave or cut any unknown material.
  • Page 60 DREMEL LC40 CONTROL SOFTWARE RUN PERIMETER HEAT – Adjust how quickly the laser is firing, or how much heat is generated on the Laser head will move along the exterior surface of the work piece. Turning up the perimeter of the job. Click again to stop this heat will cause charring for materials like motion, otherwise it will continue running.
  • Page 61 DREMEL LC40 CONTROL SOFTWARE ENGRAVE Reducing the depth will keep the surface of the work piece relatively flat or even. This function darkens or removes the SPEED – Adjust how quickly the Laser Head surface of the work piece, rather than moves.

  • Page 62: Tests & Alignments

    TESTS & ALIGNMENTS Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.

  • Page 63: Corner Mirror Alignment Test

    Air Assist Nozzle), or incomplete Thermal cutting. For this alignment test the Paper Dremel LC40 Laser Cutter must be “test fired” once in each corner of the machine. Focus Lens This is done to make sure the Laser Beam...
  • Page 64 Paper Diameter 5. Close the Lid. 6. Using the LCD touch screen display, ig. 31 test fire the Dremel LC40 Laser Cutter Ideal Spot (by tapping Test Fire on the Home Location screen) from the Test Fire screen. The Mirror...

  • Page 65: Mirror Alignment Procedure

    Step 2: Preparation 5. Align Axis B-C (X-axis) Prepare your tools and workspace. 6. Centering on focus lens. (Z-axis) 1. Power On Dremel LC40 Laser Cutter: Materials needed: The machine must be powered on to • Thermal paper (supplied). When supply continue this procedure.
  • Page 66 4. Close the Lid. Thermal Paper 5. Using the Touch Screen Display, test ig. 34 fire the Dremel LC40 Laser Cutter from the Test Fire screen. The Fire button will appear after all of the Mirror #1 system checks have passed. Press the button one time and observe where the spot lands on the thermal paper.
  • Page 67 TESTS & ALIGNMENTS Step 4: Align Axis A-B (Y-Axis) ig. 36 using Alignment Laser's Red Dot. Mirror #2 Conceptually, you will be aligning the invisible cutting beam and the Alignment Laser's visible red dot with the axis of the Fire B1 shaft from A to B.
  • Page 68 Mirror #3 when the Dremel g. If the red dot does not match the LC40 Laser Cutter is fired. Look for new Spot B2, tweak the red dot the Alignment Laser.
  • Page 69 TESTS & ALIGNMENTS Step 6: Align Axis Lens holder d. Loosen the two Mirror #3 mounting screws (Fig. 38) enough to rotate (z-Axis) using Alignment Laser's the lens in the direction of the Red Dot missing spot. While holding the lens, Centering of the beam on the lens is the retighten.

  • Page 70: Tube Guard Removal

    LASER TUBE GUARD REMOVAL Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.

  • Page 71: Operating The Dremel Lc40 Laser Cutter

    OPERATING THE LASER CUTTER Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.
  • Page 72 OPERATING THE LASER CUTTER Laser Cutting / Engraving Prohibited Uses & Restrictions The Dremele LC40 Laser Cutter may be used only for lawful purposes. Dremel does not recommend nor endorse the use of the Dremel LC40 Laser Cutter to create material that is: Prohibited by local, state or federal law;...

  • Page 73: Create A Project

    3) Focus the Laser Head. file was created, a project is developed 4) Send the job to the Dremel LC40 to run a job that will allow the Dremel Laser Cutter. LC40 Laser Cutter to cut, engrave and/or score the material. Table 5 below lists 5) System check.
  • Page 74 (image file) + text outline (vector file) = text and circle cut out Multiple files can be sent to the Dremel LC40 Laser Cutter as a single job. Simply import multiple files. If multiple files are exported from the same source file, the LC40 Control...
  • Page 75 OPERATING THE LASER CUTTER Source C) On-board Camera Capture There are two ways to use the camera 4. The camera will then capture 9 capture feature. The first way is to use different images of the bed and stitch the camera to pull a picture of the them together.
  • Page 76 Import Project Files Once the project file(s) are created they Import PDF or SVG files for objects can be imported into the Dremel LC40 you would like to cut or score. Laser Cutter and executed. Import JPEG, PNG, or PDF files for 1.
  • Page 77 4. Adjust print settings as needed. If the The material library will automatically settings are changed in this box, they populate suggested cut and/or engrave will override Dremel recommended print settings based on the material settings until a new material is and thickness selected.
  • Page 78 OPERATING THE LASER CUTTER Step 2: Place Material on the Honeycomb Plate Observe all provided warnings and safety instructions when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, Never engrave or cut property damage or personal injury.
  • Page 79 OPERATING THE LASER CUTTER Step 3: Focus the Laser Head The bottom of the Laser Head must be at ig. 44 the correct distance from the top surface of the work piece in order to cut or engrave a clean image. To focus the Laser Head (Fig.
  • Page 80 OPERATING THE LASER CUTTER Step 4: Send the Job to the Laser Close the Dremel LC40 Laser Cutter Lid. The “Run Perimeter” feature on the LCD laser screen or in the LC40 Control Software can be utilized to ensure that the work piece and the design are aligned.
  • Page 81 Step 6: Run the Job Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.

  • Page 82: Maintenance

    MAINTENANCE Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Disconnect the plug from the power source before making any assembly, adjustments or changing accessories.
  • Page 83 Use light Aperture pressure. Cleaning the interior: The interior of the Dremel LC40 Laser Cutter should be kept clean of debris. Check at least once per week and clean if necessary. Keeping the interior clean will...

  • Page 84: Troubleshooting

    MAINTENANCE Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Tension is difficult to measure but...

  • Page 85: Shipping & Storage

    SHIPPING AND STORAGE Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death.

  • Page 86: Serviceable Parts

    SERVICEABLE PARTS Observe all provided warnings and safety instructions prior to and when using the Dremel LC40 Laser Cutter. Failure to do so may result in fire, equipment damage, property damage and/or personal injury, up to and including death. Have your laser cutter serviced by a qualified repair person using only identical replacement parts.

  • Page 87: Firmware And Open Source Software

    P.O. Box 081126 Racine, WI USA 53408-1126 The request should include: (i) the name of the Dremel product, (ii) the serial number (if applicable), (iii) the software version (if applicable), (iv) your name, (v) your company name (if applicable) and (vi) your return mailing and email address (if available).

  • Page 88: Dremel Limited Warranty

    ® Limited Warranty Your Dremel LC40 is warranted against defective materials or workmanship for a period of one year form the date of Purchase with the exception of the following consumables: All lenses, mirrors and Laser Tube. The consumables (all mirrors, lenses and Laser Tube) are warranted against defective materials or workmanship for a period of 60 days from the date of Purchase.

Table of Contents