Zanussi Z814W85BI User Manual
  1. Manuals
  2. Brands
  3. Zanussi Manuals
  4. Washer
  5. Z814W85BI
  6. User manual

Zanussi Z814W85BI User Manual

Hide thumbs Also See for Z814W85BI:
Table of Contents

Advertisement

Quick Links

User Manual
GETTING
STARTED?
EASY.
Z814W85BI
EN User Manual
Washing Machine

Advertisement

Table of Contents
loading

Related Manuals for Zanussi Z814W85BI

Summary of Contents for Zanussi Z814W85BI

  • Page 1 User Manual GETTING STARTED? EASY. Z814W85BI EN User Manual Washing Machine...

  • Page 2: Safety Information

    SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.

  • Page 3: Safety Instructions

    areas for communal use in blocks of flats or in launderettes. – Do not exceed the maximum load of 8 kg (refer to the • "Programme chart" chapter). The operating water pressure at the water entry point from the • outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa).

  • Page 4: Electrical Connection

    ELECTRICAL CONNECTION • You can extend the drain hose to maximum 400 cm. Contact the Authorised Service Centre for WARNING! Risk of fire and electric the other drain hose and the extension. shock. • The appliance must be earthed. WARNING! Risk of injury, electric •...
  • Page 5 THE APPLIANCE IS EQUIPPED WITH ... UNPACKING WARNING! Use the gloves. WARNING! Remove all the packaging and the transit bolts before installing the appliance. 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recom- mended that this action is carries out by two persons.

  • Page 6: Installation On Suspended Flooring

    4. Return the appliance in vertical position and remove the socket polystyrene protection. 5. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appli- ance in factory.

  • Page 7: Positioning And Levelling

    If possible, install the appliance where the floor is more stable. POSITIONING AND LEVELLING 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the ap- pliance. Bring the appliance near the furniture recess before levelling it.
  • Page 8 The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the prop- er direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance.
  • Page 9 To a stand pipe with vent-hole Directly into a drain pipe at a height of not less than Ø 40 mm 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e.

  • Page 10: Installing Anti-Tilting Device

    If hoses run behind the appliance, make 596 mm 553 mm sure that nothing closes the small re- cess indicated with the measures 50 x 50 mm. 819 mm 50 mm 50 mm 140 mm 76 mm The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum.

  • Page 11: Preparation And Assembly Of The Cupboard Door

    1. Remove the screws of the top cover on the rear of the appliance and install the anti-tilting device as shown in the drawing. 2. Adjust the anti-tilting device so that the distance from the counter is 10mm. Loosen the nut counter- ~10mm clockwise with a 3mm wrench.
  • Page 12 Reversibility of the cupboard door Carry out the cupboard door reversibility before the appliance is built in completely. If the cupboard door has to be opened from left to right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. Make sure that the plate with magnet is on the upper position.
  • Page 13 Set the position of the lower hole respecting dimen- sions and distances shown in the drawing (449 16-22 mm mm). Countersink the holes. Ø 35 mm 12,5 - 14 mm 22±1,5 mm 595-598 mm Hinges To mount the hinges it is necessary to drill two holes (dia.

  • Page 14: Product Description

    Counter-magnet The appliance is pre set for a magnetic closure. For a correct closure: 1. Position the screw C and the counter-magnet D on the magnetic plate N. Lean the cupboard door against the screw until it leaves a mark. 2.

  • Page 15: Control Panel Description

    CONTROL PANEL CONTROL PANEL DESCRIPTION Extra Rinse touch button The child lock option is set by holding Prewash touch button pressed the relative button for at least Spin reduction options touch button 3 seconds. • Rinse Hold option Programme dial •...

  • Page 16: Dial And Buttons

    Door locked indicator. Delay start indicator. The digital indicator can show: • Reset position ( • Programme duration (e. g. • Delay time (e. g. • Cycle end ( • Warning code (e.g. • Error indicator ( Time Manager indicator. Anti-stain indicator.

  • Page 17: Permanent Extra Rinse

    Use this option for people with allergies to • Rinse Hold . The related indicator comes detergent residues and with sensitive skin. The final spin is not performed. The water of the This option increases the programme last rinse is not drained out to prevent the duration.

  • Page 18: Programme Chart

    FLEXTIME With this option you can reduce the programme duration depending on the load size and the degree of soiling. When you set a washing programme, the display indicator shows the default duration and dashes. Touch Flextime button to reduce the programme duration according to your needs.
  • Page 19 Programme Reference Default tempera- spin speed Maximum Programme description ture Spin speed load (Type of load and soil level) Temperature range range (rpm) 1400 rpm 8 kg White cotton and fast-coloured cotton. Normal (1400 - soil. The energy consumption decreases and the time Cottons Eco 400) of the washing programme is extended, ensuring good...
  • Page 20 Programme Reference Default tempera- spin speed Maximum Programme description ture Spin speed load (Type of load and soil level) Temperature range range (rpm) 900 rpm Single synthetic blanket, padded clothes, du- Duvet (900 - vets, down jackets and similar items. 3 kg 40 °C 400)

  • Page 21: Acoustic Signals

    Programme Cottons ■ ■ ■ ■ ■ ■ ■ ■ ■ Synthetics ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Delicates ■ ■ ■ ■ ■ ■ ■ Easy Iron ■ ■ ■ ■...

  • Page 22: Before First Use

    CHILD LOCK The appliance will default to this option after you switch it off. With this option you can prevent children from playing with the control panel. The Child Lock function may not be available for a few seconds after switching the appliance on. To activate/deactivate this option, hold down the Plus Steam button until comes on/goes off...

  • Page 23: Check The Position Of The Detergent Flap

    • Do not set the delay start function. - Maximum level for quantity of liquid ad- 5. Measure out the detergent and the fabric ditives. conditioner. 6. Carefully close the detergent dispenser. - Flap for powder or liquid detergent. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated...
  • Page 24 STARTING A PROGRAMME WITH THE DELAY At the end of the load detection, in case of drum START overload, the indicator is flashing in the 1. Touch the Delay Start button repeatedly until the display: display shows the desired delay time. On the In this case, for 30 seconds, it is possible to pause display the indicator shows the appliance and remove the exceeding garments.
  • Page 25 If the AutoAdjust System has When you activate the appliance completed and the water filling has again, the display shows the end of already started, the new programme the previous programme. Turn the starts without repeating the programme dial to set a new cycle. AutoAdjust System.

  • Page 26: Hints And Tips

    The display shows the end of the last If you set a programme or an option programme. that ends with water in the drum, the Turn the programme dial to set a new cycle. Stand-by function doesn't If the dial is rotated to the "Reset" position , the deactivate the appliance to remind appliance automatically turns off in 30 seconds.

  • Page 27: Care And Cleaning

    • Always start a washing programme with the softener for washing machines. In areas where the maximum load of laundry allowed. water hardness is soft it is not necessary to use a • If you pre-treat the stains or use a stain remover, water softener.

  • Page 28: Cleaning The Detergent Dispenser

    Use a small brush to clean the recess. Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears. CLEANING THE DETERGENT DISPENSER To prevent possible deposits of dried detergent or clotted fabric softener and/or formation of mould in...
  • Page 29 1. Open the pump cover. 2. Place a suitable bowl below the drain pump access to collect the water that flows out. Always keep a rag nearby to dry up any water spill- ages when removing the filter. 180˚ 3. Turn the filter 180 degrees in anti-clockwise direc- tion to open it, without removing.
  • Page 30 7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Cen- tre. 8. Clean the filter under the water tap. 9.

  • Page 31: Troubleshooting

    CLEANING THE INLET HOSE AND THE VALVE FILTER 45° 20° EMERGENCY DRAIN 1. Disconnect the mains plug from the mains socket. If the appliance cannot drain the water, carry out 2. Close the water tap. the same procedure, described in 'Cleaning the 3.

  • Page 32: Possible Failures

    First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. WARNING! Deactivate the appliance before carrying out any check. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: •...
  • Page 33 Problem Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. The appliance does not fill • Make sure that the water tap is not clogged.

  • Page 34: Emergency Door Opening

    Problem Possible solution • The AutoAdjust System is able to adjust the programme duration The programme duration according to the type and the laundry load size. Refer to "The Au- increases or decreases during programme execu- toAdjust System load detection" in "Daily Use" chapter. tion.

  • Page 35: Consumption Values

    CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different cau- ses can change the data: the quantity and type of laundry and ambient temperature. Wa- ter pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration.

  • Page 36: Technical Data

    PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION 1369/2017 Product Information Sheet Trade Mark ZANUSSI Model Z814W85BI, PNC914580500 Rated capacity in kg Energy efficiency class A+++ Energy consumption in kWh per year, based on 220 standard wash- ing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes.

  • Page 37: Environmental Concerns

    Power consumption of the off-mode in W 0.30 Power consumption in left-on mode in W 0.30 Water consumption in litres per year, based on 220 standard wash- ing cycles for cotton programmes at 60 °C and 40 °C at full and 10999 partial load.
  • Page 40 WWW.ZANUSSI.COM/SHOP...

Table of Contents