Bosch PMF 220 CE Original Instructions Manual page 17

Working without the Auxiliary Handle
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑4 (Sanding),
EN 62841‑2‑11 (Cutting):
2 2
Sanding: a =10 m/s , K=1.5 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
2
Scraping: a =12 m/s , K=1.5 m/s
h
Working with the auxiliary handle
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑4 (Sanding),
EN 62841‑2‑11 (Cutting):
2 2
Sanding: a =9 m/s , K=1.5 m/s ,
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
2
Scraping: a =16 m/s , K=1.5 m/s
h
The vibration level and noise emission value given in these in-
structions have been measured in accordance with a stand-
ardised measuring procedure detailed in EN 62841 and may
be used to compare power tools. They may also be used for a
preliminary estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
The following table shows examples of application tools. You can find additional application tools in Bosch's extensive range of
accessories.
Application tool
Bi-metal segment
saw blade
Sanding plate for
Delta series 93 mm
sanding sheets
Profile sander
Bi-metal plunge cut
saw blade for wood
and metal
Bosch Power Tools
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
,
2 2
power tool and application tools, keeping their hands warm,
=16 m/s , K=2 m/s ,
h
2 2 and organising workflows correctly.
=14 m/s , K=3 m/s ,
h
2
.
Fitting
u
Changing the tool
2 2
=17 m/s , K=2 m/s ,
h
u
2 2
=18.5 m/s , K=3 m/s ,
h
2
.
Selecting an Application Tool
Please observe the application tools intended for your power
tool.
Application tool
Material
Wood-based materials,
plastic, non-ferrous
metals
Depends on the sanding
sheet
Wood, pipes/profiles,
paint, varnish, filler, metal
Softwood, soft plastics,
plasterboard, thin-walled
aluminium profiles and
non-ferrous metal pro-
files, thin sheet metal,
Pull the plug out of the socket before carrying out any
work on the power tool.
Wear protective gloves when changing tools. There is
a risk of injury when touching the application tools.
Application
Separating cuts and plunge saw cuts;
including sawing close to edges, in corners and in difficult-
to-reach areas;
example: Shortening skirting boards that are already in-
stalled or door frames, plunge cuts when adapting floor
panels
Sanding surfaces at edges, in corners or in difficult-to-
reach areas;
depending on the sanding sheet, e.g. for sanding wood,
paint, varnish, stone;
fleeces for cleaning and for texturing wood, removing rust
from metal and for keying varnish, polishing felt for pre-
polishing
Convenient and efficient sanding of profiles up to a dia-
meter of 55 mm;
red sanding sheets for sanding wood, pipes/profiles, var-
nish, filler and metal
Small separating cuts and plunge cuts;
example: Cutting a recess for sockets, cutting a copper
pipe so that it is flush with a surface, making plunge cuts in
plasterboard
1 609 92A 4BL | (01.10.2018)
English | 17
PMF 220 CE
PMF 2000 CE