Page 1
Before Start- ing Assembly and Use. Save This Manual For Future Reference. SEARS, ROEBUCK d_o-15A- oo SWAIRS / r.RRFTSMRN® 51_.INCH JOINTER-- • assembly • operating • repair parts AN D CO., Dept. 698/731A, Sears Tower, Ch icago, PLANER IL 60684...
WARRANTY SERVICE IS AVAILABLE CENTER IN THE UNITED STATES. This warranty gives you specific state to state. Sears, Roebuck and Co. Dept. 698/731A, Sears Tower, Chicago, GENERAL SAFETY RULES FOR POWER TOOLS 1. KNOW YOUR POWER TOOL For your safety,...
Page 3
GENERAL SAFETY RULES FOR POWER TOOLS ... UNPACKING AND CHECKING CONTENTS SAFETY RULES FOR JOINTER-PLANER ASSEMBLY Depth of Cut Hand Knob Chip Deflector Checking Cutter Blades ... Fence ...
Page 4
UNPACKING Model 149.236320 Jointer-Planer is shipped complete carton. Separate all parts from packing materials with the illustration and the list of loose parts to make certain all items are accounted for, before discarding material. If any parts are missing, do not attempt...
SAFETY RULES FOR JOINTER--PLANER Safety is a combination of operator common sense and alertness at all times when the Jointer--Planer used. Study these rules and general safety rules before operating and retain them for future use. 1. WEAR EYE PROTECTION.
CUTTER BLADES POSITION CORD IS UNPLUGGED CAUTION: MAKE SURE THE SWITCH CEEDING WITH CHECKING CUTTER BLADES. The blades in your Joint÷r-Planer have been factory to assure proper operation. Shipping ever, may cause misalignment. For accurate must be .003-in. higher than...
A= 11/16 Thick x 2" Wide x 10" Long The 11/16 thickness can be obtained by planing the jointer-planer. B= 112" to 314" Thick x 3-1/2" Wide x 10" Long This piece may also be made out of plywood. C= 314" Thick x 2-1/2" Wide x 19-1/2" Long The 2-112"...
INSTALLING If the Jointer-Planer is to be used in a permanent should be fastened securely to a firm supporting as a workbench. Holes should be drilled surface of the workbench as illustrated. Each foot of the Jointer- Planer should be bolted securely using 5/16"...
CAUTION: IF THE CUTTER GUARD FAILS TO OPERATE PROPERLY, CUTTER GUARD RETURN WILL NEED REPLACING. CONTACT YOUR NEAREST SEARS STORE OR SERVICE CENTER FOR REPLACE- MENT SPRING AND INSTRUCTIONS BEFORE THE JOINTER--PLANER. SWITCH \ SWITCH KEY SPRING USING...
BASIC JOINTER---PLANER For your safety do not exceed a 1/16" deep cut on a planing operation for work pieces wider than 1-1/2". For work pieces less than 1.112", a 118" cut can be taken at a slow feed rate. This Jointer-Planer...
WHILE FEEDING, CLEAN _CAUTION: DOWN/PUSH IMMEDIATELY WITH SANDPAPER. BEVELING AND CHAMFERING The fence on your jointer-planer is adjustable to 45 ° outboard. Adjust the fence to desired lock knobs. BEVELING is the cutting of. an angle on the entire board, Beveling...
CHIP EXHAUST- VACUUM PORT IF THE CUTTER GUARD FAILS TO OPERATE (SEE "CONTROLS ADJUSTMENTS" CONTACT YOUR NEAREST SEARS STORE FOR REPLACEMENT SPRING BEFORE USING THE JOINTER--PLANER. AND IN-...
Clean them frequently with Sears Remover stock number 49191. ,_WARNING: DO NOT AT ANY TIME LET BRAKE GASOLINE, PENETRATING OILS, TACT WITH PLASTIC PARTS.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • MODEL NUMBER: 149.236320 All parts listed may be ordered from any Sears Service Center and most Sears stores. If the parts you need are not stocked transmitted to a Sears Repair Parts Distribution AND CO., Dept.