Pillar Drill. WARNING! critical Symbols most NOTE: These should also points understood followed the YELLOW IMPORTANT! be read. Symbol may be ”59“" ‘0 information Y°"- finally the GREEN NOTE! symbol Wolf—106302 Page...
Warranty choice with You have made excellent Congratulations! also Our commitment quality of this Quality product purchase service. Should you. expectations, experience includes contrary faults during private to material manufacturing detects shall be liable of the date of warranty within 24 months purchase that;...
Page 6
WARNING] There four label which be found symbols warning pillar dnll, warning the purpose of wamrng make symbols possible hazardous condillons. Remember Ihal aware alrmrnale safety danger subsmute accrdenr prevenuon messages proper measures. Wolf. 106302 Page...
Damaged cables increase the risk of electric shock. Check extension cables regularly signs damage. Damaged extension cables must Cable replaced. reels should be used when unrolled, only fully Wolf—106302 Page...
Keep away hair fitting caught Loose clothes, jewellery long parts. moving parts. fitted, these collection devices ensure dust extraction devices these correctly operated. Using connected dust. danger posed by reduces Wolf-106302 Page —...
Page 9
Tool Use & Care Service clamps vice secure support work Pillar drill area servicing must qualified repair performed by stable platform. Holding work hand against body Sen/ice pertcn‘ned by unqualified your maintenance person. is unstable and may lead loss of control. could result in risk of person...
Mount your pillar removed from the chuck before connecting chuck sure iailure could result in possible serious injury. comply power ON. turning source power Wolf—106302 Page...
Page 11
(230V/50Hz), of the consult electrician first. electricity provisions, Even variations of the power considering supply (:10% the rotational speed of the spindle will 230V), never exceed the rated no-load speed. Wolf'— rooaoz Page —...
Page 12
This includes personal Ensure you have all the tools required assembly operation. approved protective equipment. in the NOTE: If any plug parts damaged missing, attempt cord the switch until the damaged turn missing parts power installed obtalned correctly. Wolf". 106302 Page...
Page 13
Unscrew turning chuck sleeve. Secure chuck using key. in the headstock screws avoid obstructing internal diameter NOTE: The otthe height guard secured adyusted headstock. Align nuts Wing stock horizontally '<:able base. Secure Wolf—106302 with Allen screws. Page...
Page 14
0-45°. scale from been re-connected. start Set the table required angle drill pillar Note: press green the bolt. graduated retighten button. We recommend pillar drill, scale stop guidance. press button, engineers protractor WORK‘TABLE EVOTED when setting angles. \Volf‘.106302.Pagei4...
Page 15
Spindle speeds adjusting belt tension WARNING: that pillar drill is switched off and ensure Always A De“ m” NOTE 9°S“‘°”'”9 ‘5 Speed from before unplugged supply making adjustments power loosed the inside coverot drill p.llar changing drill bll, Changing spindle speed Unscrew head securing...
Page 16
Loosen securing the hole distance from the drill workpiece plus depth Calculate require. bolt to collar depth stop accordingly, tighten securing adjusting maintain this position, drill is ready drilling. pillar ruler. measurements using engineers Always check Wolf-106302 Page...
When drilling material, lubricate the drill with oil. Correct drilling speeds Factors which determine best speed kind material are: being worked, size of hole, type drilling cutter, quality desired. \Volf' 106302 Page »...
Lubricate drive with oil six months. spindle every spindle guide should also be checked screw regularly This does contain that product parts repaired by consumer. Please contact technical if you assistance 0330 123 0001 department require \Vo'F-106302 Page —...
Page 20
Ltd., Hereby We UK Home Shopping equipment below described EN 601029-1/A11:2010 EN ISO 12100:2010 Pillar Drill and function: Wolf Speed Description Serial Numbers: 00332 of Manufacture: 2017 Year 55014-1A2:2011 Munufacture’s within EN 55014-2/A2:2008 authorised representative Prospect Close,...