Whirlpool WFC8090GX Service Manual
  1. Manuals
  2. Brands
  3. Whirlpool Manuals
  4. Washer
  5. WFC8090GX
  6. Service manual

Whirlpool WFC8090GX Service Manual

2.8 cu ft smart all-in-one washer & dryer
Hide thumbs Also See for WFC8090GX:
Table of Contents

Advertisement

Quick Links

L-96
SERVICE MANUAL
WHIRLPOOL 2.8 CU FT SMART
ALL-IN-ONE WASHER & DRYER
WFC8090GX
W11243198

Advertisement

Table of Contents
loading

Related Manuals for Whirlpool WFC8090GX

Summary of Contents for Whirlpool WFC8090GX

  • Page 1 L-96 SERVICE MANUAL WHIRLPOOL 2.8 CU FT SMART ALL-IN-ONE WASHER & DRYER WFC8090GX W11243198...
  • Page 2 FORWARD This Whirlpool Service Manual, (Part No. W11243198), provides the In-Home Service Professional with service information for the “WHIRLPOOL 2.8 CU FT SMART ALL-IN-ONE WASHER & DRYER.” The Wiring Diagram used in this Service Manual is typical and should be used for training purposes only.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS WHIRLPOOL SMART ALL-IN-ONE WASHER & DRYER SECTION 1 — GENERAL INFORMATION WASHER/DRYER SAFETY ........................1-2 INTRODUCTION ..........................1-3 CONTROL PANEL AND FEATURES .......................1-4 CONTROL PANEL - TOOLS ........................1-5 LOAD & GO BULK DISPENSER ......................1-5 THEORY OF OPERATION ........................1-6 PRODUCT SPECIFICATIONS ........................1-7 WIRING DIAGRAM LOCATION ......................1-8...
  • Page 4 TABLE OF CONTENTS (CONT.) WHIRLPOOL SMART ALL-IN-ONE WASHER & DRYER SECTION 4 — COMPONENT ACCESS REMOVING THE DOOR ASSEMBLY .....................4-2 REMOVING THE TOP PANEL .......................4-3 REPLACING THE HUMAN-MACHINE INTERFACE ................4-4 REMOVING THE FRONT PANEL & BULKHEAD ..................4-6 REMOVING THE REAR ACCESS PANEL ....................4-7 REMOVING THE INLET VALVE ASSEMBLY ..................4-8...

  • Page 5: Section 1 - General Information

    GENERAL INFORMATION Section 1: General Information This section provides general safety, parts, and information for the “Whirlpool Smart All-In-One Washer & Dryer.” n Washer & Dryer Safety n General Information n Control Panel and Features n Load & Go Bulk Dispenser...

  • Page 6: Washer/Dryer Safety

    You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 7: Introduction

    “X” on the touch screen to the right of the estimated time remaining. Accessories: Pedestal with Storage: WFP2411GX Color-matched pedestals raise the washer/dryer to a more Smart Appliance with Remote Control comfortable working height. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 8: Control Panel And Features

    Stores and accesses your favorite cycles. LCD SCREEN Use this screen to select cycle, settings, options, etc. REMOTE ENABLE BUTTON Touch this button to be able to use the Whirlpool ™ to control the washer/dryer. Download the Whirlpool ™ and follow the instructions to connect your washer/dryer to your home Wi-Fi network.

  • Page 9: Load & Go Bulk Dispenser

    Restore Factory, WiFi Terms and Conditions, and Software If a dry cycle is interrupted and the load removed before Terms and Conditions. Follow the screen prompts. the cool-down period at the end of the cycle, the load will be very hot. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 10: Theory Of Operation

    Dry Cycle - Illustration Air Heater Blower Heater Channel Inlet Air NTC Cooling Valve Condenser Duct Sump NTC Drain Pump Figure 1 - Dry Cycle Theory of Operation Whirlpool Smart All-In-One Washer & Dryer...

  • Page 11: Product Specifications

    240 VAC Frequency : 60 Hz Amps : Water Supply : 20-100 psi (137.9–689.6 kPa) DETAILS Capacity : WFC8090GX = 2.8 Cu Ft Size : 24” Wide Motor Drive Type : Direct Drive Motor Horsepower : 1/2 HP Interior Light :...

  • Page 12: Wiring Diagram Location

    GENERAL INFORMATION Wiring Diagram & Model/Serial Number Location Wiring Diagram Location Model & Serial Number Label Location (Access under top panel on top of dispenser assembly) Figure - Wiring Diagram, Model/Serial Number Location Whirlpool Smart All-In-One Washer & Dryer...

  • Page 13: Model And Serial Number Nomenclature

    TF = HEFEI, CHINA YEAR OF PRODUCTION 8 = 2018, 9 = 2019 WEEK OF PRODUCTION 2 Digits that represent the week of the year PRODUCT SEQUENCE NUMBER 5 Digits that represent the unique product number Whirlpool Smart All-In-One Washer & Dryer...

  • Page 14: All-In-One Washer/Dryer Maintenance

    Use an affresh® Machine Cleaning Wipe or mild soap and water. IMPORTANT: To avoid damaging the washer/dryer finish, do not use abrasive products. 1-10 Whirlpool Smart All-In-One Washer & Dryer...
  • Page 15 3. Put 1 qt. (1 L) of R.V.-type antifreeze in drum and run washer on Normal cycle for about 2 minutes to mix antifreeze and remaining water. 4. Unplug washer/dryer or disconnect power. Whirlpool Smart All-In-One Washer & Dryer 1-11...

  • Page 16: Cleaning The Drain Pump Filter/Draining Residual Water

    Empty the container. Repeat this procedure if necessary until all the water has drained. Make sure that the black hose is Black hose completely dry. Black hose 1-12 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 17: How To Manually Open A Locked Door

    • Drive Motor drain pump filter access door • Wash Heater/Temp Sensor Assembly right corner at the front of the With a Phillips head screwdriver, Whirlpool Smart All-In-One Washer & Dryer 1-13 Components accessible through bottom move the Phillips head screw...
  • Page 18 GENERAL INFORMATION Notes 1-14 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 19: Section 2 - Diagnostics & Troubleshooting

    DIAGNOSTICS & TROUBLESHOOTING Section 2: Diagnostics & Troubleshooting This section provides diagnostic, fault codes, and troubleshooting information for the “Whirlpool Smart All-In- One Washer & Dryer.” n Control Panel n Abbreviations n Diagnostic Guide n Service Diagnostic Mode n Activating Service Diagnostic Mode...
  • Page 20 DIAGNOSTICS & TROUBLESHOOTING FOR SERVICE TECHNICIAN’S USE ONLY For Service Technician Use Only Whirlpool Smart All-In-One Washer & Dryer DO NOT REMOVE OR DESTROY...

  • Page 21: Abbreviations

    DIAGNOSTICS HOME screen, press the < button in the top left - Press and release the TOOLS button ( corner of the screen twice, and then press the HOME button. - Repeat this 3 button sequence 2 more times Whirlpool Smart All-In-One Washer & Dryer...
  • Page 22 System Info System Info Scroll down and select Scroll down and select Component Activation Component Activation “Component Activation” “Component Activation” WiFi WiFi Figure 2 Whirlpool Smart All-In-One Washer & Dryer Motor Turn Left and Right Motor Turn Left and Right...
  • Page 23 • Turn “Motor Turn Left and Right” Off • Turn “Dry Fan” Off < Component Activation Motor Turn Left /CCW Motor Turn Left and Right – – Figure 4 Figure 6 Whirlpool Smart All-In-One Washer & Dryer Continued on following page . . .

  • Page 24: Fault/Error Codes

    To exit Fault/Error Codes Display Mode, turn the cycle selector knob or press and hold POWER. The fault codes below may be indicated under various conditions and can be accessed through Service Diagnostics. Whirlpool Smart All-In-One Washer & Dryer F0E1 Load in drum during Clean Washer cycle...
  • Page 25 See TEST #6: Pressure Switch, pg. -10. F3E2 Wash NTC open or shorted See TEST #9: Wash Temperature Sensor, pg. 3-13. See TEST #12b: Dry Thermistor Sensor, pg. 3-20. Continued on following page . . . Whirlpool Smart All-In-One Washer & Dryer...
  • Page 26 Check drain hose installation for proper height, check drain hose and filter for obstructions, and make sure drain hose is not sealed into drain pipe. Check functionality of drain/ recirculation pump. • See TEST #7: Drain/Recirculation Pump, pg. 3-11. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 27: Troubleshooting Guide

    Clean obstruction from dispenser. Valve problem See TEST #5: Inlet Valve, page 3-9. Dispenser system problem. See TEST #10a & 10b: Dispenser System, page 3-14 to 3-16. Continued on following page . . . Whirlpool Smart All-In-One Washer & Dryer...
  • Page 28 Check internal hose connections for leakage. Check bellow. Check for holes in the bellow. If there are none, remove, reposition, and reinstall the bellow. Make sure the bellow is not wrinkled. Continued on following page . . . 2-10 Whirlpool Smart All-In-One Washer & Dryer...
  • Page 29 See TEST #12b: Dry Temperature Sensor, pg. 3-20. Expected Connections between ACU and HMI. Check connections and harness continuity between ACU and HMI. ACU problem. See TEST #1: ACU Power Check, pg. 3-4. Continued on following page . . . Whirlpool Smart All-In-One Washer & Dryer 2-11...
  • Page 30 Clean filter if necessary. Refer customer to Use and Care Guide/ Clothes Are Dry in Installation Instructions. Auto Dry Setting Dryness setting for auto dry cycles. Increase dryness level setting. Thermistor problem. See TEST #12b: Dry Temperature Sensor, pg. 3-20. Notes 2-12 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 31: Section 3 - Component Testing

    Section 3: Component Testing This section provides a wiring diagram, control board specifications, testing procedures and strip circuits for the “Whirlpool Smart All-In-One Washer & Dryer.” n Testing: Safety Information n Wiring Diagram n Component Testing n TEST #1: ACU Power Check...
  • Page 32 Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet. Whirlpool Smart All-In-One Washer & Dryer...
  • Page 33 COMPONENT TESTING For Service Technician Use Only WIRING DIAGRAM Whirlpool Smart All-In-One Washer & Dryer...
  • Page 34 RFI FILTER - FIGURE 1 L1 Output to ACU J1, Pin 2 (Brown Wire) L2 Output to ACU J1, Pin 1 (Lt Blue Wire) L1 Input to RFI Filter (Red Wire) L2 Input to RFI Filter (Black Wire) Whirlpool Smart All-In-One Washer & Dryer...
  • Page 35 APS Input J5-2 Mains relay out (L1) J12-4 Switched 5V J20-3 J5-3 Mains relay out (L1) J5-4 Softener pump (L2) J12-5 Open RECIRCULATION PUMP (BR) J22-1 Mains relay out (L1) J22-2 Recirculation pump (L2) Whirlpool Smart All-In-One Washer & Dryer...

  • Page 36: Test #2: Human-Machine Interface (Hmi)

    Figure 4 - Human-Machine Interface (HMI) and Housing Assembly HUMAN-MACHINE INTERFACE (HMI) ACU Input (3 pin To Drum LED ACU Input connector) (3 pin connector) Speaker Connector Speaker Figure 2 - Connector Locations on HMI Whirlpool Smart All-In-One Washer & Dryer...

  • Page 37: Test #3: Motor Circuit

    1. Figure 1 MOTOR J36-1 J4A-1 6 - 20 Ω 6 - 20 Ω J36-2 J4A-2 6 - 20 Ω J36-3 J4A-3 MOTOR STATOR MOTOR Figure 2 - Direct Drive Motor Strip Circuit Whirlpool Smart All-In-One Washer & Dryer...

  • Page 38: Test #4: Door Lock System

    DOOR LOCK ASSEMBLY DOOR LOCK SYSTEM DOOR LOCK ASSY LOCK SOLENOID DOOR SWITCH ~170 ohms J2-3 J2-2 J2-1 LOCK SWITCH Figure 1 - Door Lock Strip Circuit Whirlpool Smart All-In-One Washer & Dryer...

  • Page 39: Test #5: Inlet Valve

    Figure 1 - Inlet Valve valves. INLET VALVE ASSEMBLY WATER VALVES MAIN FILL RFI-N RFI-L J4-6 J1-2 J4-1 J1-1 RELAY CONDENSATION J4-4 INLET VALVE 890 - 1.1K Ohms Figure 2 - Inlet Valve Strip Circuit Whirlpool Smart All-In-One Washer & Dryer...

  • Page 40: Test #6: Pressure Switch

    Figure 1 - Pressure Switch debris. PRESSURE SENSOR (APS) PRESSURE SWITCH PRESSURE SWITCH J20-1 J20-2 APS OUTPUT APS INPUT J20-3 +5 VDC +5 VDC Figure 2 - Pressure Switch 3-10 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 41: Test #7: Drain/Recirculation Pump

    Recirculation Pump (150–190 Ω) when at room temperature. Figure 1 - Drain/Recirculation Pump DRAIN/RECIRCULATION PUMP DRAIN/RECIRCULATION PUMP DRAIN PUMP 45-65 W J6-2 J4-5 RFI-L RFI-N J1-2 J1-1 RECIRCULATION PUMP 150-190 W J22-1 J22-2 Figure 2 - Drain/Recirculation Pump Strip Circuit Whirlpool Smart All-In-One Washer & Dryer 3-11...

  • Page 42: Test #8: Wash Heating Element

    DO NOT REMOVE OR DES RFI-L RFI-N 30 - 34 ohms J1-2 J9-2 J9-1 J1-1 L1 - HEATER RELAY HEATING ELEMENT L2 - HEATER RELAY Figure 3 - Wash Heating Element Strip Circuit 3-12 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 43: Test #9: Wash Temperature Sensor

    Figure 7 - Drain Pump Assembly 77°F (25°C) = 20.0 k ohms DO NOT REMOVE OR DESTROY J14-6 J14-5 +5 VDC WASH NTC WASH TEMPERATURE SENSOR Figure 2 - Wash Temperature Sensor Strip Circuit Whirlpool Smart All-In-One Washer & Dryer 3-13...

  • Page 44: Test #10A: Dispenser Sensing

    Container Position Out CONTAINER POSITION SW +5 VDC J12-2 J12-1 Detergent Level Out DETERGENT LEVEL SW +5 VDC J12-4 J12-3 Softener Level Out SOFTENER LEVEL SW Figure 2 - Detergent Sensing Strip Circuit 3-14 Whirlpool Smart All-In-One Washer & Dryer...
  • Page 45 13. Perform the Service Diagnostic Mode Tests on page 2-3 to Figure 3 - Dispenser Container Inside View verify repairs. Filters Valve Assembly Dosing Pumps Softener Detergent Lvl Switch Lvl Switch Container Switch Figure 4 - Detergent Assembly - Bottom View Whirlpool Smart All-In-One Washer & Dryer 3-15...

  • Page 46: Test #10B: Dispenser Metering Pumps

    METERING PUMPS DISPENSER DOSING PUMPS DETERGENT PUMP J5-2 J5-1 RFI-L RFI-N J1-1 J1-2 FABRIC SOFTENER PUMP J5-3 J5-4 Figure 3 - Detergent & Fabric Softener Metering Pumps Strip Circuit 3-16 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 47: Test #11: Supply Connections-U.s

    L1 and L2 on the of the plug is connected to the top contact ACU. See figure 10b. Whirlpool Smart All-In-One Washer & Dryer 3-17 on the terminal block and make a note of it.

  • Page 48: Test #11: Supply Connections-Can

    ACU; and the integrity of the power cord itself. 3-18 Whirlpool Smart All-In-One Washer & Dryer 4. If it is necessary to replace the power cord, remove the retaining clip that secures...

  • Page 49: Test #12A: Dry Heating Element

    DRY HEATING ELEMENT DRY HEATING ELEMENT 30 - 50 ohms RFI-N RFI-L DRY HEATING ELEMENT J1-2 J10-2 J10-1 J1-1 L1 - HEATER RELAY L2 - HEATER RELAY Figure 3 - Dry Heating Element Strip Circuit Whirlpool Smart All-In-One Washer & Dryer 3-19...

  • Page 50: Test #12B: Dry Temperature Sensor (Ntc)

    Figure 1 - Dry NTC Location on Heater Channel Assembly DRY TEMPERATURE SENSOR DRY TEMPERATURE SENSOR (NTC) 77°F (25°C) = 20.0 k ohms J14-2 J14-1 +5 VDC DRY NTC DRY TEMPERATURE SENSOR Figure 2 - Dry Temperature Sensor (NTC) Strip Circuit 3-20 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 51: Test #13: Dry Fan Motor

    ACU and Fan Motor. DRY FAN MOTOR DRY FAN MOTOR 40 - 50 ohms RFI-L RFI-N J1-2 J7-2 JI-1 J7-1 DRY FAN MOTOR Figure 2 - Dry Fan Motor Strip Circuit Whirlpool Smart All-In-One Washer & Dryer 3-21...
  • Page 52 COMPONENT TESTING Notes 3-22 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 53: Section 4 - Component Access

    COMPONENT ACCESS Section 4: Component Access This section provides service parts, assemblies, and component locations for the “Whirlpool Smart All-In-One Washer & Dryer.” n Removing the Door Assembly n Removing the Top Panel n Replacing the Human Machine Interface (HMI)

  • Page 54: Removing The Door Assembly

    (see Figure 2 & 3). (The bag is “tucked-away” between the hinge and front panel.) Remove tape and bag, and disconnect HMI connector. Preserve the tape and bag for reassembly. Figure 5 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 55: Removing The Top Panel

    4. Lift up the bulk detergent lid and remove the bulk dispenser container (see Figures 1 & 2). Remove 2 Screws Figure 1 Figure 4 7. From the rear of the washer/dryer, pull back on top cover, lift up and remove. Figure 2 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 56: Replacing The Human-Machine Interface

    (reconnected) to the customer’s HAN and (3) hinge screws indicated in Figure 3. Remove “lower” added to the customer’s account on the Whirlpool App. inner door panel and set aside for reassembly. An extra SAID & MAC Sticker is provided with the service replacement HMI.
  • Page 57 8. Using a Phillips screwdriver, remove the two (2) screws securing the hinge to the outer door/HMI assembly. Remove hinge and harness assembly and set aside for reassembly. See Figure 6. Fan Connector Speaker DO NOT REMOVE OR DESTROY Figure 6 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 58: Removing The Front Panel & Bulkhead

    Figure 1 Lift up on bulkhead to release from side panels. Remove bulkhead and set aside for reassembly. 6. Reverse procedure to reinstall bulkhead and front panel. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 59: Removing The Rear Access Panel

    4. Remove six (6) Phillips screws securing the rear access panel to the back panel as indicated in Figure 1. Remove rear access panel. Remove 6 Screws Figure 1 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 60: Removing The Inlet Valve Assembly

    Inlet Hose Connections The inlet hoses must be connected properly. The gray hose (to condenser sprayer) connects to the top valve port and the black hose (to dispenser) connects to the bottom valve port. Whirlpool Smart All-In-One Washer & Dryer...

  • Page 61: Removing The Pressure Switch

    6. Squeeze the pressure switch mounting clip to remove the pressure switch from the side panel (see Figure 1). Figure 2 9. Reverse procedure to reinstall pressure switch. Press inward on Mounting Clips Figure 1 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 62: Removing The Metering Pumps

    Fabric Softener pump has a “red” Figure 4 connector and the Detergent pump has a “white” connector (see Figure 2). 10. Reverse procedure to reinstall metering pump. Be sure to reinstall the connector wrappings, tape and wire ties. 4-10 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 63: Removing The Detergent Dispenser

    8. Remove the remaining 4 screws, illustrated in Figure 1, securing the dispenser to the washer/dryer. 9. Disconnect the black (dispenser) hose from the inlet valve. See Figure 1. Screws Removed Black Hose in Step “6” Figure 1 Whirlpool Smart All-In-One Washer & Dryer 4-11...

  • Page 64: Removing The Dryer Heating Channel Assembly

    (2) resettable thermal cutoffs, and thermistor (see Figure 1). Figure 3 - Lift heat channel to cut strap Dryer Heater DRYER CHANNEL ASSEMBLY Fan Motor Thermistor Resettable Thermal Cutoff(s) CONDENSER DUCT Figure 1 - Dryer Channel Assembly 4-12 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 65: Removing The Condenser Duct Assembly

    Clamp Screw Lower Condenser Duct CONDENSER DUCT Figure 3 Figure 1 11. Remove condenser duct assembly from washer/dryer. If necessary, remove cooling valve from condenser duct. 12. Reverse procedure to reinstall condenser duct. Whirlpool Smart All-In-One Washer & Dryer 4-13...

  • Page 66: Removing The Rfi Filter

    6. Inside the terminal box, remove the four (4) Phillips screws securing the terminal box to the rear panel (circled Figure 4 in Figure 2). 10. Reverse procedure to reinstall the RFI Filter. 4-14 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 67: Removing The Door Lock Assembly

    Panel Assembly” prior to performing the following steps. 7. Remove the spring clamp securing the outer bellows to the front bulkhead. Loosen and pull away the bellows from the opening in the bulkhead. Whirlpool Smart All-In-One Washer & Dryer 4-15...

  • Page 68: Removing The Appliance Control Unit (Acu)

    Comm), are both located next to each other at the top right corner of the ACU and can be mistakenly plugged into each other’s connector. If this occurs, it will cause a communication malfunction to both the HMI and Motor Control Unit. Figure 4 4-16 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 69: Removing The Motor Control Unit (Mcu)

    MCU Housing & PCBA MCU Cover Remove 6 Screws Figure 3 9. Slide the MCU Assembly “up” to disengage from back panel. Figure 1 10. Reverse procedure to reinstall the MCU. Whirlpool Smart All-In-One Washer & Dryer 4-17...

  • Page 70: Removing The Heater & Thermistor

    2. Turn the drum slowly after the new heater has been installed, to make sure the heater is not touching the drum. 3. Run cycle for leak testing. Remove 6 Screws Figure 1 4-18 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 71: Removing The Drain & Recirculation Pumps

    Unclip hose, drain water. Recirc. Recirculation Connector Pump Remove 4 Screws Drain Pump Figure 1 6. Gently lay washer/dryer on its right side to access the Drain and Recirculation Pumps. Drain Connector Figure 3 Whirlpool Smart All-In-One Washer & Dryer 4-19...

  • Page 72: Removing The Direct Drive Motor

    4. Remove six (6) Phillips screws securing the rear access panel to the back panel as indicated in Figure 1. Remove rear access panel. Figure 3 - Lock Rotor Receptacle Remove 6 Screws Figure 1 4-20 Whirlpool Smart All-In-One Washer & Dryer...
  • Page 73 Figure 5 IMPORTANT: Be sure to protect the rotor and stator from dust or debris during disassembly and reassembly. Debris on the rotor or stator can damage the motor during operation. Whirlpool Smart All-In-One Washer & Dryer 4-21...

  • Page 74: Removing The Tub Assembly

    14 Perform the procedures on page 4-18, “Removing the Heater and Thermistor Assembly” prior to performing the following steps. 15. Perform the procedure on page 4-20, “Removing the Direct Drive Motor” prior to performing the following steps. 4-22 Whirlpool Smart All-In-One Washer & Dryer...

  • Page 75: Section 5 - Connectivity

    CONNECTIVITY Section 5: Connectivity This section provides connectivity features, setup, operation, and troubleshooting for the “Whirlpool Smart All-In-One Washer & Dryer.” n Manually Unlocking the Door Lock System n Smart Features n Internet Connectivity Guide n WPS Connectivity Instructions n Smart Operation n Connectivity Troubleshooting Whirlpool Smart All-In-One Washer &...

  • Page 76: Smart Features

    What it does: Allows the consumer to browse additional wash WiFi connectivity allows the Smart Washer/Dryer to connect cycles available in the Whirlpool® app and download a cycle to to the Internet and interact with the Whirlpool™ app from the washer with the Download & Go™ option. The consumer your smartphone or mobile device.

  • Page 77: Internet Connectivity Guide

    If you have any problems or questions, call Whirlpool company. Corporation Connected Appliances at 1-866-333-4591. NOTE: If this is your rst Smart Appliance, you will need to download the Whirlpool app and create an online user account. ® wnload app Register your washer/dryer in your 3.

  • Page 78: Wps Connectivity Instructions

    CONNECTED button (C). refer to alternate instructions at www.whirlpool.com/connect. The Wi-Fi status indicator (B) on the washer/dryer control panel Press the WPS button on the router. An indicator light will May need to add verbiage about 180°...

  • Page 79: Smart Operation

    Smart Operation Wi-Fi connectivity allows your Smart Washer/Dryer to connect to the Internet and interact with the Whirlpool™ app from your smartphone or mobile device. This connection opens up several Smart options to you: options intended to save you valuable time and energy.

  • Page 80: Connectivity Troubleshooting

    • WiFi icon is blinking slowly Washer/dryer is connected to home WiFi router, but • WiFi icon is ON Whirlpool™ app or Smart Grid functions do not work • Blue Smart Grid icon is blinking slowly Washer/dryer is connected to home WiFi router, and the •...
  • Page 81 WARRANTY INFORMATION SOURCES IN THE UNITED STATES: FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL: FOR WHIRLPOOL PRODUCTS: 1-800-253-1301 FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL: THE TECHNICAL ASSISTANCE LINE: 1-800-832-7174 HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN...
  • Page 82 Whirlpool 2.8 CU FT Smart All-In-One Washer & Dryer W11243198...

Table of Contents