Ritron 7 Series Owner's Manual page 22

7-Series Base Station User Manual
T 5: A F
ABLE DVANCED EATURE
Code Feature
Radio Wide Features
2x Turn On Volume
30 Disable Channel Scan
31 Enable Channel Scan
40 Disable Weather Channel
41 Enable Weather Enable
50 Disable Weather Alert
51 Enable Weather Alert
60 Z Button Scan
61 Z Button Weather
62 Z Button Monitor
63 Z Button Call Tone
64 Z Button DTMF/2-Tone/Selcall
70 Turn On to Channel 1 Disabled
71 Turn On to Channel 1 Enabled
91 Call Tone Low
92 Call Tone High
Per Channel Features
110 High Power
111 Low Power
Busy Channel TX Inhibit Disable 
120
121 Busy Channel TX Inhibit Enable
130 RX Beep Disable
131 RX Beep Enable
140 TX Beep Disable
141 TX Beep Enable
150 ANI on PTT Disable
151 ANI on PTT Enable
160 Monitor Lockout Disable
161 Monitor Lockout Enable
170 Scan Resume Delay Disable
171 Scan Resume Delay Enable
Programming Readout Codes
81 Frequency Code
82 QC or DQC Tone Code
83 2-Tone, DTMF or Selcall
Encode Code
84 2-Tone, DTMF or Selcall
Decode Code
89 Reset to Factory Defaults
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
C
ODES
Key Description
Radio turns on to volume level x. (x = 0-9)
Disables Channel Scanning.

Enables Channel Scanning.
Disables Weather Channel on VHF radios only.

Enables Weather Channel on VHF radios only.

Disables Weather Alert on VHF radios only.
Enables Weather Alert on VHF radios only.

Z button enables channel scanning.
Z button enables weather channel.
Z button toggles receiver between carrier squelch and tone squelch.
Z button transmits a Call Tone.
Z Button transmits DTMF, Selcall or 2-Tone code programmed into the selected
channel.

When radio is turned on it will go to last channel used.
When radio is turned on it will go to Channel 1.

With Z Button set for Call Tone, Call Tone will be transmitted at a low level.
With Z Button set for Call Tone, Call Tone will be transmitted at a high level.

Prevents TX if a signal is present on the receiver.

Beep at the end of a received message.

Beep when radio is ready for user to talk.

DTMF or Sellcall ANI will be sent on PTT press.

Prevents monitoring channel, only message with correct tone codes will be heard.

If a signal is received while scanning, radio will remain on the channel for a period of
time after the received signal is gone before scanning is resumed.
Display will sequentially show the programmed 2 or 3-digit Frequency Code. (1)
Display will sequentially show the programmed 2-digit QC Tone Code or 3-digit DQC
Tone Code. (2)
Display will sequentially show the programmed 2-digit 2-Tone Code, or the 3 to 7-digit
DTMF or Selcall Code
Display will sequentially show the programmed 2-digit 2-Tone Code, or the 3 to 7-digit
DTMF or Selcall Code
Resets the JBS base radio to Factory default programming. Channel 1 and 2 are
reset to factory default, channels 3-10 are deleted.

KEY: The JBS Base Radio is set from the factory with these options enabled.
NOTES: (1) 999 indicates a non-table frequency or that TX and RX are not the same
(2) If the RX and TX tone codes are not the same, or if DCS is inverted you will
get an ERROR indication
(4) ERROR indication will be displayed if not a Field Programming value (has
been PC programmed)
RADIO PROGRAMMING
20