Table of Contents
Summary of Contents for Neilsen CT3656
- Page 1 14.4V LI-ION CORDLESS CLIPPER CT3656 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 3: Ec Declaration Of Conformity
EC Directive based on its design and type, as brought into circulation by In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 14.4V LI-ION CORDLESS CLIPPER Model: CT3656 Applicable EC Directives: EC Low Voltage Directive 2014/35/EU... -
Page 4: Range Of Application
It is forbidden to use it on people. Notice: The machine can not be operated unless the blades are fitter. 2. Technical data 2.1 Clipper Model NO. CT3656 Voltage 14.4V Power output Speed 2300rpm Amplitude of swing 6.5mm... - Page 5 3.1 Introduction This section describes the mandatory safety regulations which must be carried out when we use the clipping machine. All people should read the operating instructions before using the product. The operating instructions must be kept safely in the storage case at all times. 3.2 Proper Use Which the machine is used on is described in Section 2.
- Page 6 Children are strictly prohibited to operate the equipment. 3.5 Safety Instructions for charger & battery cartridge 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, please read all instructions and cautionary markings on battery charger、...
-
Page 7: Operation
exceed 50° C. 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge will explode in a fire. 8. Be careful not to drop, shake or strike battery. 9. Do not pack anything in a box or container. The battery should be placed in a well ventilated area during charging. - Page 8 4.2 Adjust blades pressure with the adjustment cap Before putting into operation, make adjustment as follows: Before clipping: With the machine switched off, we should tighten the adjustment cap (Figure 2, part 5) until it can clip hair smoothly(Figure 2). During clipping Pay attention to that the pressure of the blade should not be set to a value that is too high, otherwise the clipped hair may gather in the blade.
- Page 9 4.5 Replace battery cartridge 1. Please switch off the tool before inserting or removing the battery cartridge. 2. Remove the battery cartridge from the clipper by pressing the buttons on both sides of the battery cartridge. (Figure 4) 3. Insert the battery cartridge, and push to the end until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
- Page 10 5. Daily care and maintence Disconnect the power supply before starting any servicing work . Remove the battery cartridge. Do not handle the area round the clipper blades as long as the machine is still connected to a power source even if the machine switched off . We always firstly disconnect the power supply whenever working on the clipper blades or clipper head .
-
Page 11: Malfunction Analysis
6. Malfunction analysis If there is something you do not understand ,please contact the service center. MALFUNCTION CAUSE RECTIFICATION Not connect with power supply. Plug into power supply. It is necessary to repair it if you could still charge the Indicator damaged. -
Page 12: Environmental Protection And Disposal
The owner has a duty to disuse of the clipper blades as well as of the clipping machine properly at the end of service life. Please observe your relevant national regulations. The only way to dispose of a NEILSEN battery is to recycle it. The law prohibits any other method of disposal. - Page 13 Figure 4 Figure 5 Figure 6 Figure 7...
-
Page 14: Product List
10. Product list Batterry Pack Body Clipper Head Screw Clipper Head （Include Clipping Blades） Adjustment Cap Regulating Spring Aluminum Head Axis Of Deflection Deflection Collar Gear Jump Ring Bow Riece Screw Washer Upper Blade Bottom Blade Regulation Screw Slider Driving Wheel Body Left body Wire... - Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in china...