1. Manuals
  2. Brands
  3. Sarlo Manuals
  4. Trimmer
  5. WeedBoss CS-16
  6. Owner's manual

Sarlo WeedBoss CS-16 Owner's Manual

Line trimmer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Model
Shaft style
Shaft length
Engine
Cutting width
Line size
Unit weight
Head type
Starting system
Handle type
Clutch
Shoulder harness
Warranty
This unit is intended for occasional use.
OWNERS MANUAL
P O W E R E D B Y
CS-16 String Trimmer
Curved
56"
34cc 4-cycle
Briggs & Stratton
16"
.095"/2.4 mm
12.8 lbs
Bump feed
Easy starting 4-cycle
Standard loop
No
No
2 year Consumer
90 day Commercial
LINE TRIMMER
MODEL CS-16
SARLO MANUFACTURING
P.O. BOX 1169 FORT MYERS, FL 33902
PHONE: 1-800-749-5296
CONTENTS

SAFETY RULES

ASSEMBLY
OPERATION
MAINTENANCE
SERVICE/ADJUSTMENTS

TROUBLESHOOTING

NOTES
STORAGE

ILLUSTRATED PARTS LIST

WARRANTY INFORMATION

PAGE
1
2
3
4
5
6
6
7
8-9
10
P/N 10006 12/03

Advertisement

Table of Contents
loading

Related Manuals for Sarlo WeedBoss CS-16

Summary of Contents for Sarlo WeedBoss CS-16

  • Page 1: Safety Rules

    Model CS-16 String Trimmer Shaft style Curved Shaft length 56" Engine 34cc 4-cycle Briggs & Stratton Cutting width 16" Line size .095"/2.4 mm Unit weight 12.8 lbs Head type Bump feed Starting system Easy starting 4-cycle Handle type Standard loop...

  • Page 2: Rules For Safe Operation

    WARNING: Do not operate without the cutting attachment shield in place. Keep all from the rotating cutting attachment. WARNING: Never use blades or flailing devices. This unit is designed for line trimmer use only. Use of any other accessories or attachments will increase the risk of injury.

  • Page 3: Safety Rules

    • Do not allow a person to use this unit unless instructions are read and understood. Never allow children to operate or play with the unit. • Do not operate this unit when tired, ill or under the influence of alcohol, drugs, or medication. •...

  • Page 4: Assembly

    ASSEMBLY INSTRUCTIONS I TOOL LIST • Screwdriver (Phillips or Standard) • Allen wrench 4mm • 10mm wrench I INSTALLING CUTTING HEAD • While locking the gear shaft by inserting a pin into the upper holder and the housing. • Rotate the cutting head to clockwise to engage threads.

  • Page 5: Operating Instructions

    Clippings are thrown away from the operator. • Slowly move the trimmer into and out of the cutting area at the desired height. Move either in a forward-backward or side-to-side motion. Cutting shorter lengths produces the best results.

  • Page 6: Operation

    Refer to your BRIGGS & STRATTON owners’ manual for engine information 1. Adding oil to a new unit 2. Adding fuel 3. Starting a NEW engine 4. Starting and Stopping Periodic Maintenance Chart WARNING: Accidental engine starting can cause injury. Always remove the spark plug before servicing the engine to prevent accidental starting.

  • Page 7: Service/Adjustments

    SERVICE/ADJUSTMENTS SAFETY RULES 1. Shut down the trimmer to make certain the head cannot turn while working with the head. 2. Check mounting of cutting head on trimmer and tighten if it is loose 3. Inspect head for wear, chips or cracks. Replace parts or entire head if needed.

  • Page 8: Troubleshooting

    TROUBLESHOOTING GUIDE Case 1. Starting failure CHECK Fuel tank Fuel filter Carburetor idle speed screw No spark Spark plug Case 2. Engine starts but does not keep running/Hard re-starting CHECK Fuel tank Carburetor idle speed screw Muffler, cylinder(exhaust port) Air cleaner Cylinder fin, fan cover If your unit needs further service, please consult with an authorized service dealer in your area.

  • Page 9: Storage

    • Lightly oil external metal surfaces. • This trimmer may be stored in a variety of positions. If possible, it is preferred to store the trimmer in a horizontal position with the spark plug up. The trimmer should not be stored or transported with the spark plug down.

  • Page 10: Illustrated Parts List

    ILLUSTRATED PARTS LIST CURVED SHAFT CS-16 Engine 10032 10041 10231 10236 10235 10212 10014 10017 10016 10015 10000 10221 10220 10238 10237 10239 10200 10002 10210 10211 10222...

  • Page 11: Illustrated Parts List

    SS-18/CS-16 WARNING: IT IS UNSAFE TO USE ANY AFTER MARKET HEAD, ATTACHMENT, ACCESSORY OR BLADE ON THIS UNIT. USE ONLY HEADS, ATTACHMENTS, BLADES AND ACCESSORIES MANUFACTURED BY SARLO AND INTENDED FOR THIS SPECIFIC MODEL. Quantity Description Decal for pipe Label...
  • Page 12 Sarlo will repair or replace, free of charge any part or parts of the units found upon examination by any Factory Authorized Dealer or by the factory to be defective in materials and or workmanship for the term of the warranty.

Table of Contents