Model BC-8 Brushcutter Shaft style Curved Shaft length 62.5" Engine 34cc 4-cycle Briggs & Stratton Cutting width 17" w/line 8" w/blade Line size .095"/2.4 mm Unit weight 13.7 lbs Head type Bump feed and 8" diameter blade included Starting system...
RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator’s manual describes safety and international symbols and pictographs that appear on this product. Read the operator’s manual for complete safety, assembly, operating, maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning or caution.
Page 3
• Do not allow a person to use this unit unless instructions are read and understood. Never allow children to operate or play with the unit. • Do not operate this unit when tired, ill or under the influence of alcohol, drugs, or medication. •...
Page 4
Maintain proper control until the blade has completely stopped rotating. WARNING: IT IS UNSAFE TO USE ANY AFTER MARKET HEAD, ATTACHMENT, ACCESSORY OR BLADE ON THIS UNIT. USE ONLY HEADS, ATTACHMENTS, BLADES AND ACCESSORIES MANUFACTURED BY SARLO AND INTENDED FOR THIS SPECIFIC MODEL. SAFETY RULES...
ASSEMBLY INSTRUCTIONS I TOOL LIST • Screwdriver (Phillips or Standard) • Allen wrench 4mm • 10mm wrench I INSTALLING CUTTING HEAD • See page 9 for blade removal instructions. • Make sure debris shield with line cut off is properly installed. See next page. •...
FIRMLY WITH A 4mm ALLEN WRENCH. Fig. 1 SHIELD ASSEMBLY FOR BRUSH CUTTER BLADE THE BRACKET (FIG. 2) MUST BE MOUNTED TO THE SHIELD WITH THE OPEN SIDE DOWN AS SHOWN. SECURE THE BRACKET AND SHIELD TO THE GEAR BOX WITH THE 4 SCREWS INCLUDED. THE TOP OF THE BRACKET MUST BE EVEN WITH THE TOP OF THE SHIELD.
OPERATING INSTRUCTIONS USING THE CUTTING BLADE WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit WARNING: Do not use the cutting blade for edging or as an edger. Severe personal injury to yourself or others can result.
OPERATING INSTRUCTIONS HOLDING THE TRIMMER WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit Before operating the unit, stand in the operating position (Fig. 5). Check for the following: • The operator is wearing eye protection and proper clothing.
Refer to your BRIGGS & STRATTON owners’ manual for engine information 1. Adding oil to a new unit 2. Adding fuel 3. Starting a NEW engine 4. Starting and Stopping Periodic Maintenance Chart WARNING: Accidental engine starting can cause injury. Always remove the spark plug before servicing the engine to prevent accidental starting.
SERVICE/ADJUSTMENTS SAFETY RULES 1. Shut down the trimmer to make certain the head cannot turn while working with the head. 2. Check mounting of cutting head on trimmer and tighten if it is loose 3. Inspect head for wear, chips or cracks. Replace parts or entire head if needed. 4.
SERVICE/ADJUSTMENTS SAFETY RULES 1. Shut down the trimmer to make certain the blade cannot turn while working with the blade. 2. Make certain the correct shield is securely attached and in the correct position. 3. Always wear gloves when working with the blade. 4.
TROUBLESHOOTING GUIDE Case 1. Starting failure CHECK Fuel tank Fuel filter Carburetor idle speed screw No spark Spark plug Case 2. Engine starts but does not keep running/Hard re-starting CHECK Fuel tank Carburetor idle speed screw Muffler, cylinder(exhaust port) Air cleaner Cylinder fin, fan cover If your unit needs further service, please consult with an authorized service dealer in your area.
WARNING: Perform the following steps after each use: • Allow engine to cool, and secure the unit before storing or transporting. • Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames form water heaters, electric motors or switches, furnaces, etc.
ILLUSTRATED PARTS LIST SEE FIG. BRUSH CUTTER BC-8 Part Number Model Used On 10000 BC-8 /SS-18 /CS-16 10003BC BC-8 10008 BC-8 10010 BC-8 /SS-18 10014 CS-16/SS-18/BC-8 10015 CS-16/SS-18/BC-8 10016 CS-16/SS-18/BC-8 10017 CS-16/SS-18/BC-8 10030 BC-8 10052 BC-8 /SS-18 10053BC BC-8 10061...
Page 16
Sarlo will repair or replace, free of charge any part or parts of the units found upon examination by any Factory Authorized Dealer or by the factory to be defective in materials and or workmanship for the term of the warranty.