Baldor VS1SP Quick Start Manual

Keypad Display - Displays status information during
Local or Remote operation. It also displays information
during parameter setup and fault or Diagnostic
Information.
Display Diagnostics -
I/O Status
I/O Function configuration
Modified parameters
Control Operation Data
Custom Units
Fault Display - 10 Faults with Time stamp
F1 - Alternates or "Toggles" between last two menu
choices or function indicated by text displayed directly
above key.
F2 - Clear faults or undo parameter edit changes or
function indicated by text displayed directly above key.
p (Up Arrow), q (Down Arrow)
t (Left Arrow), u (Right Arrow)
Moves cursor to select menu choices.
ENTER - Press ENTER to save parameter value changes.
In the display mode the ENTER key is used to directly
set the local speed reference. It is also used to select
other operations when prompted by the keypad display.
MENU - Selects the Menu display.
The following menu items are shown: Status,
Diagnostics, Fault Log, Advanced Programming, and
Basic Params.
LOCAL REMOTE - Changes between local and remote
modes.
HELP - Provides help at each display screen, setup
parameter and fault. Press to view/close help
information.
REV - When pressed, initiates a reverse direction run
command.
JOG - Initiates Jog mode when pressed. Press
FWD or REV for motion. Only active in local mode.
FWD - When pressed, initiates a forward direction run
command.
STOP - Initiates a stop command.
Status
STATUS
BASIC PARAMS
ADVANCED PROG
EVENT LOG
DIAGNOSTICS
DISPLAY OPTIONS
Basic
D A I G B A C K
Params
Advanced
Prog
Event Log
Diagnotics
Indicator Light -
(On when indicated Key is active)
FWD key with green light indicator.
REV key with green light indicator.
Display
JOG key with green light indicator.
Options
STOP key with red light indicator.
WARNING: Be sure that you are completely familiar with the safe operation of this equipment. Refer to MN764.
This equipment may be connected to other machines that have rotating parts or parts that are controlled by this equipment.
Improper use can cause serious or fatal injury. Only qualified personnel should attempt the start-up procedure or to operate or
troubleshoot this equipment.
F1601T1
STOP LOCAL
STATUS
F2401T1
F2402T1
0.0V
F2405T1
0RPM
F2403T1
0.0A
F2404T1
0.0HZ
F2413T1
DIAG 0r MAIN
F2901T1
F1401T1
BASIC MOTOR CONTROL
F1101T1
F1104T1
F2002T1
CONTROL TYPE
F2003T1
V/F Control
F1601T1
STATUS F1601T1 BACK F2401T1
F2402T1
F2405T1
F2403T1
LEVEL 1 BLOCKS
LEVEL 2 BLOCKS
F2404T1
LEVEL 3 BLOCKS
F2901T1
MODIFIED PARAMS
F2902T1
LINEAR L IST
F1401T1
F1101T1
F1104T1
F2002T1
EV. LOG STOP LOCAL
F2003T1
LOW INITIAL BUS
0 4-Jul-06 09:35:00
T S T A U S T R A C E
STOP LOCAL
DIAG
OPTION B OARDS
OPTION 1 Ethernet
OPTION 2 None
FEEDBACK None
EV. LOG 0.00r MAIN
PROG KEYPAD SETUP
KEYPAD CONTRAST
50%
DIAG F1313T1 BACK
See other side for Control Connections
CONTROL TYPE V/F Control
MOTOR RATED VOLT
MOTOR RATED AMPS
MOTOR MAG AMPS
MOTOR RATED SPD
MOTOR RATED FREQ
CALC MOTOR MODEL
ANA OFFSET TRIM
OPERATING MODE
ACCEL TIME 1
Open Vector Drive
DECEL TIME 1
MIN OUTPUT SPEED
3/4 to 450 hp
MAX OUTPUT SPEED
CONTROL TYPE Open Vector
MOTOR RATED VOLT
MOTOR RATED AMPS
MOTOR MAG AMPS
Quick Start Guide
MOTOR RATED SPD
Wiring / Power Up
MOTOR RATED FREQ
ANA OFFSET TRIM
Parameter Setting
ONE-STEP TUNING
OPERATING MODE
ACCEL TIME 1
DECEL TIME 1
MIN OUTPUT SPEED
MAX OUTPUT SPEED
Open Loop (Encoderless) Vector
V/Hz Inverter
MS764
9/09
VS1SP