Samsung SRP-350 Operator's Manual page 19

ESC T n
[Name] Select print direction in page mode.
[Format] ASCII ESC T
Hex 1B 54
Decimal 27 84
0 ≤n ≤3
[Range]
48 ≤n ≤51
[Description]
[Default] Selects the print direction and starting position in page mode.
n specifies the print direction and starting position as follows :
n Print Direction Starting Position
0, 48 Left right Upper left (A in the figure)
1, 49 Bottom to top Lower left (B in the figure)
2, 50 Right to left Lower right (C in the figure)
3, 51 Top to bottom Upper right (D in the figure)
ESC V n
Turn 90°clockwise rotation mode on/off.
[Name]
[Format] ASCII ESC V
Hex 1B 56
Decimal 27 86
0 ≤n ≤1, 48 ≤n ≤49
[Range]
Turn 90°clockwise rotation mode on/off.
[Description]
n is used as follows :
n
0, 48
1, 49
ESC W xL xH yL yH dxL dxH dyL dyH
[Name] Set printing area in page mode.
[Format] ASCII ESC W
Hex 1B 57
Decimal 27 87
0 ≤ xL xH yL yH dxL dxH dyL dyH ≤255 (except dxL=0 or dyL=dyH=0)
[Range]
[Description] The horizontal starting position, vertical starting position, printing area width,
and printing area height are defined as x0, y0, dx (inch), respectively.
x0 = [(xL + xH ×256)] ×(horizontal motion unit)]
y0 = [(yL + yH ×256)] ×(vertical motion unit)]
dx = [(dxL + dxH ×256)] ×(horizontal motion unit)]
dy = [(dyL + dyH ×256)] ×(horizontal motion unit)]
The printing area is set as shown in the figure below.
n
n
n
A→→→→
Print area
n
n
n
Function
Turn off 90°clockwise rotation mode.
Turn on 90°clockwise rotation mode.
xL xH yL yH dxL dxH dyL dyH
xL xH yL yH dxL dxH dyL dyH
xL xH yL yH dxL dxH dyL dyH
36
ESC ₩ n
[Name]
[Format]
[Range]
[Description]
ESC a n
[Name]
[Format]
←←←←C
[Range]
[Description]
ESC c 3 n
[Name]
[Format]
[Range]
[Description]
Bit
0
1
2
3
4-7
Set relative print position.
ASCII ESC nL
₩
Hex 1B 5C nL
Decimal 27 92 nL
0 ≤nL ≤255
0 ≤nH ≤255
Set the print starting position based on the current position by using the
horizontal or vertical motion unit.
* This command sets the distance from the current position to
[(nL + nH ×256) ×horizontal or vertical motion unit]
Select justification.
ASCII ESC a n
Hex 1B 61 n
Decimal 27 97 n
0 ≤nL ≤2, 48 ≤nL ≤50
Aligns all the data in one line to the specified position.
n selects the type of justification as follows :
n
0, 48 Left justification
1, 49 Centering
2, 50 Right justification
Select paper sensor(s) to output paper end signals.
ASCII ESC c 3
Hex 1B 63 33
Decimal 27 99 51
0 ≤n ≤255
Selects the paper sensor(s) to output paper end signals.
* Each bit of n is used as follows.
Off/On Hex Decimal
Off 00 0
On 01 1
Off 00 0
On 02 2
Off 00 0
On 04 4
Off 00 0
On 08 8
- - -
37
nH
nH
nH
Justification
n
n
n
Function
Paper roll near-end sensor disable.
Paper roll near-end sensor enable.
Paper roll near-end sensor disable.
Paper roll near-end sensor enable.
Paper roll end sensor disable.
Paper roll end sensor enable.
Paper roll end sensor disable.
Paper roll end sensor enable.
Undefined.