Related Manuals for Cactus X2GO
Summary of Contents for Cactus X2GO
- Page 1 X2Go SOFTWARE COMPATIBILITY IOS 8.0 & Above Android 4.4 & Above Supports Bluetooth 4.0 www.cactuswatches.com...
- Page 2 Setting Use VeryFitPro App on IOS or Android smart phone to set the X2GO as follows: Note: hardware and system of devices should meet the below requirements: iOS 8.0 & Above Android4.4 & Above Support Bluetooth4.0 1. Download VeryFitPro Search and download “VeryFitPro” from...
- Page 3 When fully charged (battery image will show full charge) attach both bands to the device. You are now ready to wear the CACTUS X2GO – adjust the length of the band and fasten the device around your...
-
Page 4: Know Your Device
Add Device list, please slide the screen Detection failed,please re search of the X2GO to wake up ID115Plus Color HR the device and then complete the connection (“bind successful”) Know your device 1. -
Page 5: Function Introduction
3. Heart Rate Monitoring Automatic heart rate monitoring is as default, and the device monitors heart rate all day automatically. 4. Interface Click the touch key to display successively Time Data Mode Heart Rate Alarm Clock Sports Mode Mode Mode Function Introduction 1.1 Time Mode Time dial can be switched on as follows:... -
Page 6: Heart Rate Mode
Before Data After Data Is Displayed Is Displayed When in heart rate mode for 1s, the X2Go starts to monitor heart rate and the figure like is displayed before the correct data is reached. When the heart rate is detected data is displayed numerically. -
Page 7: Sports Mode
Click the touch key to enter the next mode: Sports Mode Press and hold the touch key for 2s to start/close alarm clock 1.5 Sports Mode Click the touch key to enter the next sports mode; and in case there are no other sports modes, it will go back to the time mode. - Page 8 Pace/Speed Time Average pace Click the touch key to enter the next sub-mode of “Sports Underway”. Press and hold the touch key for 2s to enter any interface of Data Reading. Press and hold 2s to exit the sports mode. Note: The speed and distance of cycling can be displayed, but App needs to be connected and the cycling and App needs to start at the same time.
- Page 9 If there are no new activities before the end of countdown, automatic quitting occurs. 2) Reminder of full-ram force quit Click the touch key to confrim the full-ram force quit. When the Cactus X2Go memory is full, the user will be reminded to exit from sports mode.
- Page 10 3) Reminder of force quit for low battery During sport activities, if power is too low, Sports Mode will pause and remind the user to force quit from Sports Mode. Click the touch key to accept the force quit 4) Reminder of inaccessible Sports Mode for low battery The reminder will occur when the user tries to start Sports Mode when the...
- Page 11 You can then action photo taking by smartphone with any of the following methods: Shake your X2GO, or lift your wrist, or click the touch key. To exit camera mode, press and hold the touch key on your X2GO, or exit through the app.
- Page 12 E) Target Completion Alert / Reminder On achieving set goals, shake the X2GO to get the interface of the target completion reminder displayed. Click the touch key to quit from the reminder.
-
Page 13: Basic Specifications
E) Low battery reminder Please recharge F）Device Error Notification This interface will be displayed each time the device is opened, if an abnormality of functioning is detected Status Code: abnormality of acceleration sensor abnormality of heart rate sensor abnormality of touch key IC -04 abnormality of flash Basic Specifications Model No.: ID115Plus Color HR... - Page 14 Please refer to IEC 62321, EU ROHS Directive 2011/65/EU and revised directive. Wearing and Maintenance Our products are designed for daily use & wearing throughout the day. To keep your X2GO clean and for optimum functioning, we advise: • Keep your skin clean •...
-
Page 15: Warranty
FAQs Failure to find the device when pairing Make sure Bluetooth is ON in the smart phone & that software OS is Android 4.4 & above, or IOS 8.0 & above. Make sure the distance between the phone and the device is within 0.5 meter, and that the device is within normal Bluetooth communication distance range (within 10 meters) after pairing is finished.