How To Use Alarm Mode; Buttons And Functions; How To Set Alarm - Seiko T-4 Instructions Manual

(2) How to set timer
Ex.) To set countdown time to "3 minutes" and number of repetitions to "5"
① Press Button Ⓓ to show the Timer mode.
② Press and hold Button Ⓑ to activate the Timer Setting function. The hour digits start
flashing. With each press of Button Ⓓ, the digits to be adjusted can be selected in order.
※ Unless the timer has been reset, the Timer Setting function will not be activated. For
the method of resetting the timer, refer to "Timer operation" on P. 103.
③ With each press of Button Ⓒ, the flashing digits increase by one. (Each press
of Button Ⓐ decreases the digits by one.)
※The digits move quickly by pressing and holding Button Ⓐ or Ⓒ.
6 ④ After all the adjustments are completed, press Button
Timer Setting display. If the watch is left untouched with the digits flashing, the
display automatically returns to the Timer in 2 to 3 minutes.
Ⓒ
Ⓒ
Ⓓ
Ⓐ Ⓐ
Ⓓ
[ Hour ] [ Minutes ]
102

How to Use Alarm Mode

The alarm is a three-channel daily alarm that can be set to ring daily at three
different designated times (hour and minutes).
The alarm can be engaged or disengaged ("on" or "--") channel by channel.
【Caution】 The alarm rings according to the home time set in the Time/Calendar mode. It
cannot be set to ring according to the world time.

(1) Buttons and functions

・ Press Button Ⓓ to show the Alarm mode. After "ALARM" is shown in the top row, the alarm
channel ("AL1 - -," "AL2 - -" or "AL3 - -") appears instead. The alarm time set for each alarm
channel and the current time are shown in the middle and bottom rows, respectively.
※When the alarm is engaged, "on" is shown instead of "--," such as "AL1 on."
7
Button Ⓒ
Button Ⓑ
Button Ⓐ Button Ⓓ
104
Ⓑ to deactivate the
Ⓒ Ⓒ
Ⓓ
Ⓓ
Ⓐ Ⓐ
Ⓓ Ⓓ
[ Seconds ]
[ Number of repetitions ]
Ⓓ
Button Ⓐ：・To engage/disengage alarm
・To set flashing digits (to decrease)
Button Ⓑ（Press and hold） ：To activate alarm
setting function
Button Ⓒ：・To change over alarm channels
・To set flashing digits (to increase)
Button Ⓓ：・To show Solar Monitor mode
・To select digits to be adjusted
(flashing)
(3) Timer operation
①Checking that the timer has been reset, press Button
②Press Button Ⓒ to stop timer countdown.
③Press Button Ⓐ to reset the timer.
※The countdown can be stopped and restarted as many times as necessary by pressing Button Ⓒ.
※Even if the mode is changed to another during countdown, the timer continues counting.
※ The warning beep starts ringing 3 seconds before the set time is up, and the timeup
beep sounds for 5 seconds when the set time is up.
※To stop the timeup beep manually, press Button Ⓐ, Ⓑ, Ⓒ or Ⓓ.
Ⓒ
Start
Ⓒ
Ⓒ
※ When the remaining countdown time reaches less than
one minute during each repetition of countdown, the
Ⓓ
dots on the dial's edge light up, and go out one by one in
step with the decrease of the remaining seconds.

(2) How to set alarm

・ The alarm setting procedure is the same for all the three channels.
Ex.) To set the alarm time of "AL1" to "6:30 AM"
① Press Button Ⓒ to show "AL1." Then, press and hold Button
Alarm Setting function. The hour digits start flashing.
② With each press of Button Ⓓ, the hour and minute digits flash alternately. Press
Button Ⓓ to select the digits to be adjusted (flashing).
③ With each press of Button Ⓒ, the flashing digits increase by one. (Each press
of Button Ⓐ decreases the digits by one.)
※The digits move quickly by pressing and holding Button Ⓐ or Ⓒ.
④ After all the adjustments are completed, press Button
Alarm Setting display. If the watch is left untouched with the digits flashing, the
display automatically returns to "AL1" in 2 to 3 minutes.
※By deactivating the Alarm Setting function, the alarm is engaged automatically.
Ⓒ
Ⓐ
(Hour: 6:00 AM)
Ⓒ to start timer countdown.
Ⓒ Ⓒ Ⓒ
Stop Restart Stop
Ⓒ
Ⓒ
Ⓒ
Ⓓ
Ⓐ
(Minutes: 30 minutes)
Ⓐ
Reset
6
Ⓐ
103
Ⓑ to activate the
Ⓑ to deactivate the
7
105