Table of Contents
Advertisement
Quick Links
Insulation Displacement Connector for
MELSEC-Q Series 32-Point I/O Module
Thank you for purchasing the Mitsubishi programmable controller
MELSEC-Q series.
Prior to use, please read this and relevant manuals thorougly to fully
understand the product.
© 2002 MITSUBISHI ELECTRIC CORPORATION
User's Manual
MODEL
MODEL
CODE
IB(NA)-0800228-F(1806)MEE
Q6TA32
Q6TA32-U-JE
13JT92
Advertisement
Table of Contents
Summary of Contents for Mitsubishi Q6TA32
- Page 1 Insulation Displacement Connector for MELSEC-Q Series 32-Point I/O Module User's Manual Q6TA32 Thank you for purchasing the Mitsubishi programmable controller MELSEC-Q series. Prior to use, please read this and relevant manuals thorougly to fully understand the product. MODEL Q6TA32-U-JE MODEL...
- Page 2 SAFETY PRECAUTIONS (Read these precautions before using this product.) Before using this product, please read this manual and the relevant manuals carefully and pay full attention to safety to handle the product correctly. In this manual, the safety precautions are classified into two levels: "...
- Page 3 [INSTALLATION PRECAUTIONS] CAUTION ● Use the programmable controller in an environment that meets the general specifications given in the user's manual for the CPU module used. Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the product.
- Page 4 [STARTING AND MAINTENANCE PRECAUTIONS] WARNING ● Do not insert or pull out the wires when power is on. It may cause a malfunction or electric shock. ● Always clean or retighten fixing screws after switching power off externally in all phases. Otherwise, the I/O module may malfunction.
- Page 5 CONDITIONS OF USE FOR THE PRODUCT (1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions; i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident; and...
- Page 6 PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is limited only for the specific applications agreed to by Mitsubishi and provided further that no special quality assurance or fail-safe, redundant or other safety features which exceed the general specifications of the PRODUCTs are required.
- Page 7 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents...
-
Page 8: Table Of Contents
CONTENTS 1. OVERVIEW ....................1 2. PERFORMANCE SPECIFICATIONS............. 2 3. NAMES OF PARTS ..................3 4. HANDLING INSTRUCTIONS ................. 5 5. WIRING ......................6 5.1 Wiring Instructions ..................6 5.2 External Wiring ..................7 5.3 Wiring Procedure..................8 6. EXTERNAL DIMENSIONS ................10... - Page 9 MANUALS The following manual is related to this product. Please order it if necessary. Related manual Manual Number Manual Name (Model Code) SH-080042 I/O Module Type Building Block User's Manual (13JL99)
- Page 10 Memo...
-
Page 11: Overview
Q6TA32 insulation displacement connector for MELSEC-Q series 32-point I/O module (hereinafter referred to as the Q6TA32). The Q6TA32 is to be connected to the connector of the Q Series 40-pin connector type 32-point I/O module in order to convert the module connector into an insulation displacement connector. -
Page 12: Performance Specifications
2. PERFORMANCE SPECIFICATIONS The following table lists the performance specifications of the Q6TA32. Item Specifications Applicable model QX41, QX41-S1, QX41-S2, QX71, QY41P, QY41H, QY71 Polyvinyl chloride wire (twisted wire) Applicable wire Nominal 0.5 mm (20AWG) max. insulation diameter: 1.9 mm (0.07 inch) -
Page 13: Names Of Parts
Cover fixing screw Screw for fixing the cover (M2.6 screw) Insulation displacement Screw for fixing the Q6TA32 to the I/O module connector connector fixing screw (M2.6 screw) Connector Connector for connection to the I/O module. - Page 14 Memo...
-
Page 15: Handling Instructions
0.21 to 0.28 N • m Cover fixing screw (M2.6 screw) 0.21 to 0.28 N • m (5) When the Q6TA32 is installed to the I/O module, it is 9 mm (0.35 inch) out of the I/O module bottom. (Refer to "6. OUTLINE DRAWING".) Pay attention to the installation position. -
Page 16: Wiring
5. WIRING Wiring Instructions (1) Do not strip the insulation of the connectable wire before wiring. (2) The number of connectable wire per terminal is 1. (3) Wire the far side line B terminals first. (4) To prevent the wires from pushing the adjacent modules, connect them after pulling them toward you within the wire's tensile strength range given in the performance specifications. -
Page 17: External Wiring
*1*3 Empty 12/24VDC *1*3 Empty 12/24VDC *1 B1 and B2 of the QY71 are used at 5/12VDC. *2 The Q6TA32 does not have the terminal number A3, A4, B3 and B4. *3 B1 and B2 of the QY41H are empty. -
Page 18: Wiring Procedure
Cover fixing screw Q6TA32 Q6TA32 I/O module 2) Insert the wire along the guide inside the Q6TA32 without a gap, push it in gently with your finger to temporarily hold it, and push it far enough with the wiring tool. Front view... - Page 19 3) Install the covers to the Q6TA32 and tighten the cover fixing screws. Covers Cover fixing screw Wire Wire Wire Wire Q6TA32 Q6TA32 I/O module I/O module 4) Using a tester, make a continuity check. Tester lead-in port Wire Tester lead...
-
Page 20: External Dimensions
6. EXTERNAL DIMENSIONS (1) Q6TA32 (When mounted on an I/O module) 25 (0.99) 90 (3.55) 37 (1.46) 27.4 (1.08) (2) Q6TA32-TOL 50 (1.97) (0.37) Unit: mm (inch) - Page 21 Memo...
- Page 22 WARRANTY Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi;...