Polar Electro M460 Getting Started Manual

How to get started
Set up your new Polar M460 in the Polar Flow web service. The M460 is in
storage mode, and it wakes up in the setup. To get the most accurate and
personal training data, it's important that you're precise with the settings
in the setup.
1. Go to flow.polar.com/start and download the Polar FlowSync software,
which you need to connect your M460 to the Flow web service.
2. Open the installation package and follow the on-screen instructions for
installing the software.
3. Once the installation is complete, FlowSync opens automatically and
asks you to connect your Polar product.
4. Plug in your M460 to your computer's USB port with the USB cable. It
may take a few minutes for your M460 to wake up and start charging.
Let your computer install any suggested USB drivers.
Do not charge the device when the USB port is wet.
5. The Flow web service will be opened automatically in your internet
browser. Create a Polar account or sign in if you already have one.
6. Click Done to synchronize your settings between the M460 and the
Polar Flow web service. FlowSync status will change to completed,
once the synchronization is done.
7. If there's a firmware update available for your M460, we recommend
you install it during the setup.
Get to know your M460 Bike mount
You can install the bike mount
either on the stem of your bike,
or on the left or right hand side
of the handle bar.
Wed, 3.6.
Diary 1. Place the rubber base on the
stem/handlebar.
Settings
2. Position the bike mount on
the rubber base so that the
POLAR logo is in line with the
handlebar.
Tests
Strava Live
Segments 3. Secure the bike mount onto
the stem/handlebar with the
O-ring.
Interval
START
timer
4. Align the ledges on the back
Favorites
Start of the M460 with the slots
Cycling on the bike mount and turn
clockwise until the M460 is
in place.
LIGHT BACK UP DOWN
• Browse through the menu by pressing UP or DOWN.
• Start a training session and confirm selections with the START button.
• Return, pause and stop with the BACK button.
• Lock buttons in time view by pressing and holding LIGHT.
H10 heart rate sensor Training with your M460
Wear the comfortable strap and connector around your chest to get Press START and choose your sport. Go outdoors and away from tall
your heart rate accurately and in real time on your M460. buildings and trees to catch the GPS satellite signals. Keep your M460
still with the display facing upwards until it finds the GPS satellite
* If you bought your M460 without a heart rate sensor, not to worry, signal. When the signal is found, OK is displayed.
you can buy one at any time.
Press START again when you're ready to go.
1. Moisten the electrode area of
Choose your favorite sports and the information you want to
the strap.
follow during your sessions in the Polar Flow app or web service.
2. Clip the strap around your chest
and adjust the strap to fit snugly.
During training
3. Attach the connector.
4. Before your first training session, Take a lap:
you need to pair the heart rate
sensor with your M460. Wear Lock a zone:
press and hold START. If your heart rate goes outside the locked zone,
your heart rate sensor and press
START. Then wait for the sensor you will be notified with audio feedback.
pairing request and choose Yes.
Change Settings in Quick Menu:
Quick menu. You can change certain settings without pausing the
training recording.
You can also pair a new sensor in Settings > General settings> Pair and
sync > Pair other device.
Pause and stop training
After training, detach the heart rate sensor connector and rinse
Press BACK to pause your training session. To continue training, press
the strap under running water to keep it clean. For more detailed
START. To stop the session, press and hold BACK when paused until
instructions, see the M460 support pages at support.polar.com/
Recording ended is displayed.
en/M460.
Press START during a session.
To lock/unlock the heart rate zone you are currently in,
Press and hold LIGHT to open the