Advertisement
Quick Links
HP
COLOR LJ PRO M452/MFP 477
®
TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP CF410/11/12/13 A/X-HP 410 SERIES TONER CARTRIDGE
© 2017 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
www.uninetimaging.com
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com
Advertisement
Related Manuals for HP CF410A
Summary of Contents for HP CF410A
- Page 1 COLOR LJ PRO M452/MFP 477 ® TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF410/11/12/13 A/X-HP 410 SERIES TONER CARTRIDGE © 2017 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only. www.uninetimaging.com...
- Page 2 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE HP COLOR LJ PRO M452, MFP 477 (CF410//11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGES By Mike Josiah and the Technical Staff at UniNet First released in March 2016, the Pro M452/477 series of color laser printers are based on a 28ppm black & color, 600 DPI engine.
- Page 3 4. Needle nose pliers 5. Flat blade (common) screwdriver REQUIRED SUPPLIES 1. Color toner for use in the HP M452/477 series cartridges (check for standard or high yield) 2. New replacement chip (check color, standard or high yield) 3. New long life drum 4.
- Page 4 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 3. Slide the screwdriver inside the end cap to the place as 4. Remove the end cap. indicated and gently pry again until the end cap comes free.
- Page 5 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 6. Remove the drum from the waste chamber. 7. Remove the PCR. Clean with your preferred PCR cleaner and place aside in a clean area. 8. Remove the two wiper blade screws and the wiper blade.
- Page 6 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 9. Clean out all the waste toner from the chamber. Make sure all the wiper blade seals are clean. 10. Coat the new wiper blade with your preferred lubricant and install.
- Page 7 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 11. Install the cleaned PCR. Make sure to place a small amount of conductive grease on the black PCR holder. © 2017 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
- Page 8 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 12. On the supply chamber, remove the two screws from the gear side end cap. Remove the end cap. Be careful of the spring-loaded drum drive gear. It will come loose.
- Page 9 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 15. Remove the large and small gears as shown. 16. Slide the developer roller over and remove. Be careful not to lose the two round bushings or alignment tab.
- Page 10 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS RIGHT HAND LEFT HAND 17. There are two screws holding the doctor blade in place. The left screw is a normal thread screw. The right side uses a left-hand thread screw.
- Page 11 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 19. At this point while tight, you can fill the hopper with toner for use in the HP M252 series of printers. © 2017 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
- Page 12 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 20. Clean the doctor blade foam seals. Install the doctor blade and two screws. RIGHT HAND THREAD LEFT HAND THREAD Remember the right side uses the left-hand threaded screw! ©...
- Page 13 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 21. Install the developer roller. Make sure both ends have the bushings in place and the left side also has the tab bushing, long side up.
- Page 14 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 23. Press the inner end cap in place. 24. Install the two gears on the feed and developer roller shafts. 25. Install the drum drive gear.
- Page 15 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 27. Cut the chip holder with a flat blade in the two places indicated. Remove and replace the chip. 28. Coat the drum with your preferred lubricant and install the drum in the waste hopper.
- Page 16 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS TAB FITS INTO SLOT 29. Place the two halves together. Lift up on the small white drum gear tab, while pulling the end cap out to align them properly.
- Page 17 HP PRO M452 / MFP 477 (CF410/11/12/13 A/X-HP 410 SERIES) TONER CARTRIDGE REMANUFACTUIRNG INSTRUCTIONS 31. Install the spring. TAKING TEST PRINTS Supplies Status Page 1. Press OK to open the menus 2. Scroll until “REPORTS” appears on the display 3. Press OK 4.