Electrolyte - Atlas Copco XA146 Dd Instruction Manual

:# &  :#5 &
&
#66'4; %#4'
 $
%HIRUH KDQGOLQJ EDWWHULHV UHDG WKH UHOHYDQW VDIHW\
SUHFDXWLRQV DQG DFW DFFRUGLQJO\
If the battery is still dry, it must be activated as described in section
1.7.2.
The battery must be in operation within 2 months from being activated;
if not, it needs to be recharged first.
.'%641.;6'
 '
5HDG WKH VDIHW\ LQVWUXFWLRQV FDUHIXOO\
Electrolyte in batteries is a sulphuric acid solution in distilled water.
The solution must be made up before being introduced into the battery.
%6+8#6+0) # &4;
 #
– Take out the battery.
– Battery and electrolyte must be at equal temperature above 10°C.
– Remove cover and/or plug from each cell.
– Fill each cell with electrolyte until the level reaches 10 to 15 mm
above the plates, or to the level marked on the battery.
– Rock the battery a few times so that possible air bubbles can
escape; wait 10 minutes and check the level in each cell once
more; if required, add electrolyte.
– Refit plugs and/or cover.
– Place the battery in the compressor.
'%*#4)+0) # $#66'4;
 4
Before and after charging a battery, always check the electrolyte level
in each cell; if required, top up with distilled water only. When
charging batteries, each cell must be open, i.e. plugs and/or cover
removed.
8VH D FRPPHUFLDO DXWRPDWLF EDWWHU\ FKDUJHU DFFRUGLQJ
WR LWV PDQXIDFWXUHU¶V LQVWUXFWLRQV
Apply with preference the slow charging method and adjust the charge
current according to the following rule of thumb:
battery capacity in Ah divided by 20 gives safe charging current in
Amp.
#66'4; /#+06'0#0%'
 $
– Keep the battery clean and dry.
– Keep the electrolyte level at 10 to 15 mm above the plates or at
the indicated level; top up with distilled water only.
– Keep the terminals and clamps tight, clean, and lightely covered
with petroleum jelly.
22
 :#*5 &
& &
%*#4)'& $#66'4;

614#)'
 5
Run the compressor regularly, e.g. twice a week, until warm.
Load and unload the compressor a few times to operate the unloading
and regulating components. Close the air outlet valves after stopping.
,I WKH FRPSUHVVRU LV JRLQJ WR EH VWRUHG ZLWKRXW UXQQLQJ
IURP WLPH WR WLPH SURWHFWLYH PHDVXUHV PXVW EH WDNHQ
DV GHVFULEHG LQ D VHSDUDWH 6HUYLFH %XOOHWLQ $6% 
ZKLFK PD\ EH REWDLQHG RQ UHTXHVW
'48+%' 2#-5
 5
A Service Pak is a collection of parts to be used for a specific
maintenance measure, e.g. after 50, after 500 and after 1000 running
hours.
It guarantees that all necessary parts are replaced at the same time
keeping down time to a minimum.
The order number of the Service Paks are listed in the Atlas Copco
Parts List (ASL).
'48+%' -+65
 5
A Service Kit is a collection of parts to fit a specific repair or rebuilding
task.
It guarantees that all necessary parts are replaced at the same time
which improves the uptime of the unit.
The order numbers of the Service Kits are listed in the Atlas Copco
Parts List (ASL).
&RQWDFW $WODV &RSFR
1/24'5514 '.'/'06 18'4*#7.
 %
When a compressor element is due for overhaul, it is recommended to
have it done by Atlas Copco. This guarantees the use of genuine parts
and correct tools with care and precision.
+#$+.+6;
 .
The manufacturer does not accept any liability for any damage arising
from the use of non-original parts and for modifications, additions or
conversions made without the manufacturer's approval in writing.