Summary of Contents for TerraWave TWSD16128PHC
-
Page 1: Installation Instructions
Installation Instructions TWSD16128PHC Version 1.1 - Page 1 10521 Gulfdale, San Antonio, TX 78216 I www.terrawave.com I Email: sales@terrawave.com I Phone: 210-375-8482... - Page 2 Introduction The TWSD16128PHC is intended to be used with WLAN / Networking devices. The TWSD16128PHC is intended to be used both indoors and outdoors and to provide NEMA 3R protection with cooling and heating. Maximum internal ambient is 45 Degrees Celsius.
- Page 3 • The TWSD16128PHC exhibits a distinct change in performance. Heater / FAN The TWSD16128PHC includes a heating element as well as a cooling fan to provide protection to the internal components from extreme temperatures. CAUTION– Never touch the moving parts of the fan while in operation. Never touch the heat synch of the heating element while in operation –...
- Page 4 WARNING: To prevent the risk of electric shock and equipment damage, disconnect any and all power supplies to the enclosure before installing, maintaining or trouble shooting this product or any products inside the enclosure. Included Components The TWSD16128PHC consists of the following components: NEMA 4 Plug Cooling Thermostat Heating Thermostat...
- Page 5 This equipment should be installed on the mounting plate in the unit. Wire / Cable Routing The TWSD16128PHC comes with cable routing tie downs. These tie downs are used to provide convenient cable routing. It is important to use these cable tie downs to ensure that the cables that you install are kept away from the other components within the enclosure.
- Page 6 NEMA 4 Plug with Fly Nut Mounting Plate The TWSD16128PHC is supplied with a mounting plate to be used for attaching WLAN / Networking components. The following diagram (figure 1) shows which holes should be used when attaching approved products to the plate.
- Page 7 3.437" 3.00" 3.375" 3.312" 2.687" 3.938" 4.063" 2.875" Nothing higher than 4" from bottom Heater Fan Space Terminal Block (Figure 1) Version 1.1 - Page 7 10521 Gulfdale, San Antonio, TX 78216 I www.terrawave.com I Email: sales@terrawave.com I Phone: 210-375-8482...
- Page 8 10-32 x 3/8” counter sunk – Philips head 8-32 x 3/8” round Philips head 6-32 x 3/8” round Philips head 10-32 locking post (TerraWave has sample) 8-32 x 3/8” flat head Philips head Enclosure Mounting Holes Mounting holes have been provided in the back of the enclosure. These holes provide easy and convenient mounting of the unit.
- Page 9 Note: Loose fasteners, washers and nuts may not provide proper sealing and /or securing of the unit. Mounting Holes / Plugs Mounting Holes / Plugs (Figure 2) Version 1.1 - Page 9 10521 Gulfdale, San Antonio, TX 78216 I www.terrawave.com I Email: sales@terrawave.com I Phone: 210-375-8482...
- Page 10 Circuit Requirements The TWSD16128PHC should be connected to a 120V, 15A feeder circuit. The maximum capacity of the power receptacle in the unit is 120V, 12A. The circuit breaker of the feeder circuit is considered to be the disconnect device for TWSD16128PHC.
- Page 11 Cord Gland Bushing nut on of enclosure. Ensure that gasket inside of enclosure. (black) is on outside of enclosure when installing DO NOT OVER TIGHTEN! Version 1.1 - Page 11 10521 Gulfdale, San Antonio, TX 78216 I www.terrawave.com I Email: sales@terrawave.com I Phone: 210-375-8482...
- Page 12 NEC and local codes as applicable. Figure 5 represents the terminal block and power leads that are wired to the terminal block inside the TWSD16128PHC. The wiring should be applied as follows: 1.) The Black wire in figure 5 represents the hot lead and should be attached to the terminal block that is labeled ‘H’.