Lorex RA 110 Manual

PROGRAMMING PROCEDURE
1) Press the power switch to turn on the RA 110
2) Press the SET button, the "SET" LED will turn on and flash
3) Press the REC button, the "REC" LED will turn on and flash
4) While the "SET/REC" LED's are flashing, press the recording button on the VCR's remote
control to aim at the RX sensor.
5) The "SET/REC" LED will turn off the confirm completion of record signal programming
6) Press the "SET" button, then press the "STOP" button. Both the "SET/STOP" LED will flash
7) While the "SET/STOP" LED's are flashing, press the stop button on the VCR's remote control,
and aim it at the RX sensor
8) The "SET/STOP" LED will turn off to confirm the completion of the "STOP" signal
programming. The programming procedure is now complete.
SPECIFICATIONS
Power Source DC
Recording Time 10 - 90 seconds adjustable
TX Sensor Range 5M
External Sensor Cable 1 metre
Camera Input 4 Pin DIN connector
A/V output 4 Pin DIN connector
Video Output Level 1V p-p 75ohms
Audio Output Level 1V p-p
Operating Temperature -10 C ~ +50 C
Dimensions 143(W) x 35(H) x 111(D)mm
Weight 200g
INSTALLATION TIP
After you program the RA 110, please confirm the programming with the following
procedure:
(A) The distance between the RA 110 and the VCR should be about 1 metre, and aimed
directly at your VCR.
(B) Turn your VCR "ON" and press the "REC" button on the RA 110. Your VCR should go
into the recording mode.
(C) If the VCR does not go into the recording mode, please re-program the RA 110 again.
(D) Check the "STOP" button on the RA 110, and follow the above procedure.
Please Note: The RA 110 requires its own power supply for proper operation. Please power
up unit with the supplied adapter.
12V 500mA AC adapter
45
Universal VCR Controller
INTRODUCTION
The Universal VCR Controller is a perfect compliment to your OS 100 or OS 300 Motion
Sensor Video Security Camera. It "learns" the remote control commands to control your VCR,
and will record any activity picked up by your video security camera for playback at any time.
Contents
• VCR Control Unit
• Power adapter 110V AC / 12V DC (500mA)
• RCA cable
• External IR sender (with sensor cable)
• 4 Pin DIN cable (1 metre)
• Adhesive tape
FEATURES
• Compatible with most makes or models of consumer VCR's which can be controlled via IR
remote control
• "Learns" RECORD and STOP commands of remote control for consumer VCR via front panel
IR sensor
• "Plug n'Play" connection with any Home Sentinel TV observation system, and detects alarm
signal and activates VCR commands
• Sends RECORD and STOP commands by a rear panel infrared sender to activate VCR
• Programmable recording duration from 10~90 seconds
• Additional external IR sender with 1 metre cable included
• Separate RCA audio/video outputs for direct connection to consumer VCR
INSTALLATION
Connection to VCR and TV using RCA patch cord (A/V connection)
1) Connect the plug at the end of the OS100 or OS300 camera cable to the camera input jack
on the rear of the VCR Control unit.
2) Connect the A/V output jack on the VCR Controller to the camera input on the OS100 or
OS300 RF Control Unit, using the DIN patch cord supplied.
3) Connect the output audio and video jacks on the VCR Controller unit to the audio and video
inputs, using the supplied RCA patch cords.
4) Connect the output audio and video jacks on the VCR to the input audio and video jack on
the TV, using an RCA patch cord.
5) Plug in all units
MODEL RA 110